TB-9-2320-280-35-5

• INSTALLATION INSTRUCTIONS FOR SYSTEMS SINGLE CHANNEL GROUND AND AIRBORNE RADIO SYSTEM (SINCGARS) AN/VRC-88F, AN/VRC-89F, AN/VRC-90F FORCE XXI BATTLE COMMAND, BRIGADE-AND-BELOW (FBCB2) AN/UYK-128 (V)4
• INSTALLATION INSTRUCTIONS is changed as follows
• LIST OF EFFECTIVE PAGES
• TABLE OF CONTENTS
• TABLE OF CONTENTS-continued
• TABLE OF CONTENTS-continued
• CHAPTER 1. INTRODUCTION
• CHAPTER 2. PURPOSE OF INSTALLATION
• CHAPTER 3. COMPLETION TIME FOR INSTALLATION
• CHAPTER 4. PREPARATION FOR INSTALLATION
• Section IX. C4ISR EQUIPMENT, DISTRIBUTION, AND CONSUMABLES
• Table 4-1. Kit Parts List for Installation of C4ISR Equipment.
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment.
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
• CHAPTER 5. INSTALLATION PROCEDURES
• Figure 5-2.
• Figure 5-3.
• Install five nut sleeves
• Section IV. B-BEAM PREPARATION
• Section V. ASSEMBLY OF CAB ENCLOSURE PANEL
• Section VI. FINAL ASSEMBLY, TERMINAL BOARD WIRING, AND TERMINAL LINK
• Connect wire
• Route 24V power cable
• Install cab enclosure panel
• Secure three 24V fusewire assemblies
• Section VII. INTEGRATED RACK INSTALLATION
• Remove paint from vicinity of three mounting slots
• Section VIII. INSTALLATION OF SINCGARS MOUNTING TRAY AND AMP GUARD
• Section IX. FBCB2 COMPONENTS INSTALLATION
• Install ramball mount
• Section IX.A. SERIAL INTERFACE ADAPTER DEVICE (SIAD) CABLES INSTALLATION
• Section IX.B. SERIAL INTERFACE ADAPTER DEVICE (SIAD) INSTALLATION
• Section IX.C. FBCB2 CABLES INSTALLATION
• Install Vehicular Amplifier Adapter (VAA)
• Section X. LOUDSPEAKER INSTALLATION
• Using mounting plate
• Install mounting plate
• Attach loudspeaker
• Section XI. LOUDSPEAKER CABLES INSTALLATION
• Section XII. PLGR BRACKET INSTALLATION
• Section XIII. PLGR POWER CABLE ROUTING
• Attach shrink tubing
• Section XIV. ANTENNA ASSEMBLY
• Section XV. SINCGARS ANTENNA MOUNTING
• Locate and drill out second rivet
• Using support bracket
• Remove paint from all mounting holes
• Attach antenna mounting bracket
• Install front grill
• Remove ten screws
• Using support bracket
• Remove paint from both sides of mounting holes
• Attach antenna mounting bracket
• Install front grill
• Remove antenna mount plate
• Remove nine screws
• Locate and drill out second rivet
• Place support bracket
• Secure top of support bracket
• Install front grill
• Using support bracket
• Remove paint from mounting holes
• Attach antenna mounting bracket
• Remove nine screws
• Locate and drill out second rivet
• Place support bracket
• Secure bottom of support bracket
• Install front grill
• Section XVI: EPLRS ANTENNA MOUNTING
• Section XVII: EPLRS MOUNTING
• Mount resilient mount
• Insert four screws
• Position EPLRS mounting plate
• Section XVIII. URO BRACKET MOUNTING
• Section XIX: ANTENNA CABLE ROUTING
• Figure 5-77.
• Connect RF cable
• Route RF cable
• Figure 5-81
• Feed PLGR antenna cable
• Figure 5-83.
• Locate, mark, and drill 1.00-inch diameter hole
• Figure 5-85.
• Connect PLGR antenna cable
• Route RF cable
• Feed RF cable
• Figure 5-89.
• Connect RF cable
• Figure 5-92.
• Thread PLGR antenna cable
• Route PLGR antenna cable
• Figure 5-96
• Route PLGR antenna cable
• Connect RF cable
• Figure 5-99
• Figure 5-100
• Route PLGR antenna cable
• Figure 5-103
• Thread PLGR antenna cable
• Route PLGR antenna cable
• Figure 5-107
• Figure 5-108
• Route PLGR antenna cable
• Connect RF cable
• Section XX: EPLRS CABLE ROUTING
• Coil EPLRS power cable
• Route EPLRS power cable
• Figure 5-114.
• Route EPLRS power cable
• Attach shrink tubing
• Section XXI. DVE HOOD CABLE GUIDE INSTALLATION
• Locate, mark, and cut area
• Section XXII. DVE PAN AND TILT MODULE (PTM) MOUNT ASSEMBLY PREPARATION AND PILLAR MOUNT INSTALLATION
• Section XXIII. DVE A-FRAME CABLE GUIDE AND PAN AND TILT MODULE (PTM) MOUNT ASSEMBLY INSTALLATION
• Figure 5-120
• Using A-frame cable guide
• Install PTM mount assembly
• Section XXIV. DRIVER'S NBC AIR LINE AND HEATER REMOVAL
• Figure 5-123
• Section XXV. DCM ROOF MOUNTING ASSEMBLY INSTALLATION
• Figure 5-124.
• Section XXVI. PAN AND TILT MODULE (PTM) CONTROL MOUNTING BRACKET INSTALLATION
• Figure 5-126.
• Section XXVII. PAN AND TILT MODULE (PTM) CONTROL ASSEMBLY, CONTROL CABLE ASSEMBLY, AND DCM/PTM INTERCONNECT CABLE INSTALLATION
• Figure 5-128.
• Secure PTM connector end
• Figure 5-131.
• Install control cable seal assembly rubber grommet
• Section XXVIII. STOWAGE ASSEMBLY INSTALLATION
• Section XXIX. DVE POWER CABLE INSTALLATION
• Figure 5-139.
• Blank Page
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• TB-9-2320-280-35-5
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• Blank Page
• Blank Page
• Distribution
• Blank Page
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• Blank Page
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Distribution

Privacy Statement - Press Release - Copyright Information. - Contact Us