Click here to make tpub.com your Home Page

Page Title: CHAPTER 4. DEPOT MAINTENANCE
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



TM 11-5820-695-35
CHAPTER 4
DEPOT MAINTENANCE
Section I. REPAIRS
4-1. General
4-2. General Parts Replacement Techniques
a. General instructions on parts replacement for
direct support maintenance must also be observed during
depot maintenance activity. Refer to paragraph 3-19 for
a. Depot maintenance repair procedures, which
general parts replacement techniques.
supplement repair data in chapter 3, are provided in this
b. If conformal coating on printed wiring boards is
section. Depot repair consists primarily of removal and
removed during maintenance, recoat the printed wiring
replacement procedures for defective subassemblies or
boards following the instructions provided in paragraph 4-
piece parts.  Most subassemblies and piece parts are
13.
readily accessible and are easily replaced.
Repair
instructions, therefore, are supplied only for those
assemblies requiring special techniques or a sequence of
4-3. Equipment Required
steps which are not readily obvious.
Tools and materials required to perform the depot repairs
given in this section are listed below:
b. Special instructions for particular assemblies of
a. Tool pit, Radio Repair TK-100/G, FSN 6180-0-79.
Transmitter,  Radio  T-1054(P)/GRC-144()  and  T-
b. Tool Kit, Electronic Equipment TK-105/G, FSN
1054(P)A/GRC-144 are covered in paragraphs 4-4
5180-610-8177.
through 4-9; particular assemblies of Receiver, Radio R-
c. Crimping tool MS 3191-4 with head assembly
1467(P)/GRC-144()
and
R-1467(P)A/GRC144
are
W25, FSN 5120-230-771.
Special
d. Extraction tool MS 18278, Size 20, FSN 5120-
instructions for particular assemblies of Converter-
230-3770.
Multiplier
CV-3633/GRC-144(V)
are
covered
in
e. Extraction tool CET-C6B, FSN 5120-963-7661.
paragraphs 4-11.1 through 4-11.4.
4-4. Repair of Transmitter Frequency Mixer Stage 1A9
(fig. 6-71)
Transmitter frequency mixer stage 1A9 contains coaxial
c. Throughout equipment repair, reference should
circulator 1A9HYI, replaceable at direct support level
be made to wiring diagram and parts location illustrations.
(para 3-26) and is nonrepairable, and crystal mixer
I1lustrations supplied in this chapter supplement those
1A9A1, replaceable at organizational maintenance level
located in chapters 3 and 5, and those contained in TM
(TM 11-5820-695-12).
115820-695-12.  Wiring diagrams and parts location
For depot repair of crystal mixer 1A9A1, specific
diagrams for Transmitter, Radio T-1054(P)/GRC-I44() and
instructions are provided for the replacement of crystal
T-1054(P)A/GRC-144 are provided in figures 4-6 through
diode 1AOA1CR1.  Instructions for the removal and
4-35 and 5-59 through 5-89; illustrations for Receiver,
replacement of crystal diode 1A9A1CR1 are provided in a
Radio R-1467(P)/GRC-144V) and R-1467(P)A/GRC-144
and b below.
are provided in figures 4-36 through 4-46 and 5-90
CAUTION
through 5-97. The wiring diagram for Indicator, Antenna
Before
handling
crystal
Alignment ID-1708 GRC is provided in figure 4-47. Parts
1A9A1CRI,
ground
yourself
to
location diagrams for Converter-Multiplier CV3633/GRC-
equipment case ground in order to
144(V) are provided in figures 5-108 through 5-118.
dissipate any static charge.
a, Removal of Crystal Diode 1A9A1CR1 (fig. 5-71).
Change 6
4-1


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business