Click here to make tpub.com your Home Page

Page Title: Replacement.
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



TM 11-5820-695-35
securing connector 2A15W2J1 to preselector support,
diode amplifier 2A2 by rotating the knurled connector on
then remove connector and replace hex nut on
coaxial cable 2A15W1 in a counterclockwise direction.
connector (fig. 3-19).
(5)  Loosen the four captive screws (fig.
(16) Remove two nuts on the left side and
818) securing tunnel diode amplifier 2A2 to its mounting
two nuts on the right side of preselector support securing
bracket a few turns each.
preselector support to electrical equipment cabinet 2A15
(6)  Disconnect  the  knurled  connector
and remove preselector support.
INPUT J1 on tunnel diode amplifier 2A2 from its mating
(17) Remove power supply 2A1 from
connector on preselector bandpass filter 2FL4 by
electrical equipment cabinet 2A15 (para 340(4) and (5)).
rotating the knurled connector clockwise.
(18) Tag, unsolder, and remove the wires
(7)  Remove the four captive screws
connected to power transformer 2A15W4T1 terminals.
securing tunnel diode amplifier 2A2 to its mounting
Care should be taken not to put stress on the cable
bracket.
harness wires.
(8)  Slide tunnel diode amplifier 2A2 back
(19) While supporting power transformer
and to the right, then forward being careful not to put
2A15A4T1, remove the four nuts and washers securing
stress on the power cable connected to the rear of 2A2.
2A15A4T1 to its mounting bracket and then remove
(9)  Disconnect power cable 2A15W2P2
2A15A4T1 from electrical equipment cabinet 2A15.
from the POWER J3 connector (locater at the rear of
b.
Replacement.
2A2) by rotating the connector 1/2-turn clockwise (as
viewed from front of 2A2) and remove tunnel diode
(1)  Mount replacement power transformer
amplifier 2A2 from the cabinet.
2A15A4T1 on its four mounting studs in electrical
equipment cabinet 2A15.
(10) Remove eight input waveguide flange
screws (fig.  3-20) securing external input waveguide
(2)  While supporting power transformer
section to waveguide flange on preselector bandpass
2A15A4T1 flush against the transformer mounting
filter 2FL4.
bracket, replace and tighten the four nuts and washers
securing power transformer 2A15A4T1 in place.
NOTE
CAUTION
After removing the six screws (step a
Exercise care while soldering the
(11) below); obtain a thin sheet of
cable harness leads to the power
rigid material about 1/16th inch thick
transformer  terminals  to  prevent
and insert this material between the
damage to the cable harness leads or
top of the cabinet and the input
the power transformer terminals.
waveguide section to support the
input  waveguide  section  when
(3)  Solder the wires removed in step
preselector bandpass filter 2FL4 is
a(18) to power transformer 2A15A4T1 terminals.
being removed.
(4)
Replace power supply 2A1 (para 3 0g
4
(11) Remove six 2FL4 flange screws (fig.
(4) and (6'5)).
3-20) securing preselector bandpass filter 2FL4 to the
(5)  Place preselector support in electrical
top of electrical equipment cabinet 2A15.
equipment cabinet 2A15 aligning all mounting holes.
(12) Remove two bolts and washers (fig.
Then secure preselector support to electrical equipment
318) securing lower part of preselector bandpass filter
cabinet 2A15 using hardware removed in stepai (16).
2FL4 to electrical equipment cabinet 2A15 preselector
(6)  Secure tunnel diode amplifier 2A2
support and remove preselector bandpass filter 2FL4.
mounting bracket to preselector support using hardware
(13) Remove 2A16W1P1 from 2A15W2J1
removed in step a(14).
(fig.
318) on electrical equipment cabinet 2A165
(7)  Remove  hex-nut  from  connector
preselector support by rotating the knurled connector on
2A15W2J1 and insert through mounting hole on
2A16W1P1 counterclockwise.
preselector support; then secure connector 2A15W2J1
(14) Remove two nuts, washers and bolts
to mounting bracket with the hex-nut.
securing tunnel diode amplifier 2A2 mounting bracket to
(8)  Connect 2A16W1P1 to connector
electrical equipment cabinet 2A16 preselector support.
2A15W2J1 on preselector support.
(15) Remove
the
mounting
hex
nut
3-68


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business