 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|  quantity authorized in the 51100 allowance
zations authorized additional prescribed loads will
column. Example, authorized allowance for 51
multiply the number of prescribed loads author-
100 equipments is 40; for 150 equipments multiply
ized by the quantity of repair parts reflected in
40 by 1.50 or 60 parts required.
the appropriate density column to obtain the total
quantity of repair parts authorized.
h. 1-Year Allowances Per 100 Equipments/
Contingency Planning Purposes. Indicates oppo-
(3) Organizational units providing mainte-
site the first appearance of each item the total
nance for more than 100 of these equipments
quantity required for distribution and contin-
shall determine the total quantity of parts re-
gency planning purposes. The range of items in-
quired by converting the equipment quantity to
dicates total quantities of all authorized items
a decimal factor by placing a decimal point before
required to provide for adequate support of 100
the next to last digit of the number to indicate
equipments for one year.
hundredths, and multiplying the decimal factor
by the parts quantity authorized in the 51100
i. Depot Maintenance A l l o w a n c e Per 100
allowance column. Example, authorized allow-
Equipments. Indicates opposite the first appear-
ance for 51100 equipments is 12; for 140 equip-
ance of each item the total quantity authorized
ments multiply 12 by 1.40 or 16.80 rounded off
for depot maintenance of 100 equipments. Subse-
to 17 parts required.
quent appearances of the same item will have the
letters "REF" in the allowance column. Items
(4) Subsequent changes to allowances will
authorized for use as required, but not for initial
be limited as follows: No change in the range of
stockage, are identified with an asterisk in the
items is authorized. If additional items are con-
allowance column.
sidered necessary, recommendation should be for-
warded to Commanding General, U.S. Army Elec-
j. Illustration.
tronics Command, ATTN: AMSEL-ME-NMP
(1) Figure number. Indicates the figure
EM, Fort Monmouth, N.J. 07703, for exception
number of the illustration in which the item is
or revision to the allowance list. Revisions to the
shown.
range of items authorized will be made by the
(2) Item number or reference designation.
USA ECOM National Maintenance Point based
Indicates the callout number or reference designa-
upon engineering experience, demand data, or
tion used to identify the item in the illustration.
TAERS information.
g. 30-Day DS/GS Maintenance Allowances.
NOTE
a. Identifications of the usable on codes of this
Allowances in GS Column are for GS
publication are--
maintenance only.
Code
Used on
l-
----
- - - - AN/TMQ5
(1) The allowance columns are divided into
2-
----
- - - - AN/TMQ-5A
three subcolumns. Indicated in each subcolumn,
3
---
- - AN/TMQ-5B
opposite the first appearance of each item, is the
4-
---
- - - AN/TMQ-5C
total quantity of items authorized for the number
5-
---
- - - CY-1390/TMQ-5
of equipments supported. Subsequent appear-
6-
---
- - - CY-1390A/TMQ-5
ances of the same item wil have the letters "REF"
7-
---
- - - MX-1482/TMQ-5,
in the applicable allowance columns. Items au-
Order No. 3133PL51
thorized for use as required, but not for initial
8 - - - - - - - - - - MX-l482/TMQ-5,
stockage, are identified with an asterisk in the
Order No. 19934-PL-55
allowance column.
9- - - - - - - - - MX-1482/TMQ-5,
(2) The quantitative allowances for DS/GS
Order No. 29116-PP-58
levels of maintenance will represent initial stock-
10- - - - - - - C-834/TMQ-5
age for a 30-day period for the number of equip-
11- - - - - - - - C-834A/TMQ-5
ments supported.
12- - - - - - - - CV-146/TMQ-5
(3) Determination of the total quantity of
13- - - - - - - CV-l46A/TMQ-5
parts required for maintenance of more than 100
1 4 - - - - - - PP-968/TMQ-5
of these equipments can be accomplished by con-
15- - - - - - - - PP-968A/TMQ-5
verting the equipment quantity to a decimal fac-
16- - - - - - - - - - - RD-88/TMQ-5
tor by placing a decimal point before the next to
17- - - - - - - - - - - - RD-88A/TMQ-5
last digit of the number to indicate hundredths,
18- - - - - - - - - - RD88B/TMQ-5
and multiplying the decimal factor by the parts
19- - - - - - - - R5-88C/TMQ-5
iv
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals