Unpacking Instructions - TM-11-5826-258-240015

TM 11-5826-258-24

Table 1-3. Packaging Data

Volume

Weight

Carton size (in.) (id)

Component

Item net dim (in.)

(cu ft)

(lb)

4.00

9.75 x 6.62 x 12.25

0.46

5.13 x 5.75 x 2.625

Control, Receiver C-10048/ARN-l23(V)1

0.89

12.00

11.25 x 8.12 x 17

Receiver, Radio R-2023/ARN-123(V) or R-2139/ARN-123 (V)

11.93 x 4.12 x 7.18

17-1/8 x 9-3/4 x 4-1/8

0.40

2.00

Mounting

Base,

Electrical

Equipment

MT-1834/ARN-123(V)

13.62 X 4.38 X 2.25

14-1/4 x 9-1/4 x 3-114

0.25

2.00

13.62 x 7.12 x 1.17

Mounting Base, Electrical Equipment MT-4980/ARN-l23(V)

2.20

19.00

17-3/4 x 11-5/8 x 18-1/2

Consolidation

box

a. Place each item within a plastic bag fabricated of

1-17. Unpacking Instructions

material conforming to L-P-378. Wrap the item in

To unpack the equipment, open the carton, and

cellilosic cushioning m a t e r i a l conforming to

remove the technical manual. Remove each indi-

PPP-B-843, type II, a minimum of 6 inches on all sur-

vidual box from the consolidation container. Open

faces and secure the wrap with tape conforming to

the component boxes, exercising care when remov-

PPP-T-45. Place the cushioned item within a close-fit-

ing the items to prevent damage to the components

ting fiberboard box conforming to PPP-B-636, W5c

or destruction of the cartons, plastic bag, or the

and seal all seams and joints with tape conforming to

internal dunnage. Do not dispose of the packaging

PPP-T-76.

materials.

b. When individual components are being shipped,

NOTE

the packaged item shall be overpacked within a close-

The reusable containers shalll be retained

fitting box.

for use in repackaging and shipping between

c. When more than one item is being shipped, a

the Government and contractor's overhaul

quantity of the packaged items shall be overpacked

facility.

within a close-fitting box.

d. Substitute packaging materials may be selected

1-18. Checking Unpacked Equipment

from those items listed in SB 38-100.

a. Inspect the equipment for damage that may have

occurred during shipment. If the equipment has been

1-20. Shipment Marking

damaged, or packaging deficiencies are discovered, fill

out and forward DD Form 6 (AR 700-58).

The packed radio sets or individual items with appro-

b. Check to see that the equipment is complete as

priate copy of DA Form 2407 shall be addressed to the

listed on the packaging slip. If the packing slip is not

contractor marked as follows:

available, check the equipment against the items listed

Bendix Corporation

in table 1-3.

Avionics Division

2100 N.W. 62nd Street

1-19. Repacking

Ft. Lauderdale, Florida 33310

Repackage the equipment using reverse procedure in

ATTN: CONUS Repair Service Administrator

paragraph 1-17 and figure 1-4. If the original packag-

Reliability Improvement Warranty

ing materials are not available for use, package the

Contract DAAB07-75-C-0853

M/F:

For Repair and Direct Return

equipment as follows:

Change 1

1-9