Click here to make tpub.com your Home Page

Page Title: Control Pabel A1A4 Removal
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



TM
11-5820-919-40-1
1.
Remove  the  2  mounting  screws  (38)
4.
"Loosen the 5 captive screws (not
and  washers  for  multipin  connector
shown)  connecting  the  shield  to  the
A1A3J3 (37) located on the back side of
power  supply.
receiver/exciter
housing.
5.
Remove
the
shield.
2.
Carefully  fold  back
multipin
CONTROL
PANEL
A1A4
REMOVAL.
connector  A1A3J3  (37)0
1.
Place
the  receiver/exciter  so  that
the  control
panel  cover  assembly  (7)  is
Remove  the  2  mounting  screws  (32)
3.
on top.
and  washers  for  connector  plug  A1A2J4
One  screw  is  located  under
(33).
CAUTION
multipin  connector  A1A2J3  (37)  ribbon
cable.
Do  not  place  control  panel
so that it will fall out when
captive  screws  are  loosened.
Remove  mounting  screws  (39)  and
4.
Flexible  cable  to  housing
washers  for  multipin  connector  A1A1J2
could  be  damaged.
(40) .
5.
Remove  receptacle  connector  J1
2.
Loosen  the  6  captive  screws  (22)
(29)  by  removing  the  two  mounting  nuts
on  the  control  panel  cover  assembly  (7).
(28)  from  the  connector  studs  (36)  and
pull  connector  (29)  backwards,  carefully
Pull the panel (7) out by grasping
3.
folding,  leaving  circuit  board  mounting
the  audio connector  plugs  A1A4J1  and  J2
Allen  screws  (42)  visible.
(21).
CAUTION
CAUTION
When control  panel  is  dis-
Use  extreme  care  when  removing
attached  from  radio,  care
or  replacing  ribbon  cables.
should  be  taken  to  prevent
Creasing  or  severe  bending  will
static
discharge.
damage  ribbon  cables
internally.
Locate  the
multipin
connector
(23)
4.
and  ribbon  cable
(26).
Remove  printed  circuit  board  and
6.
cable  assembly  A1W1  (25);  pull  upward,
5.
Loosen the 2 captive Allen screws
removing  it  from  the  receiver/exciter
(24).
housing.
Pull the ribbon cable (26) and mul-
5.
tipin
connector  (23)  apart.
RECEIVER/EXCITER
REASSEMBLY
RIBBON
CABLE
W1
REMOVAL.
NOTE
Procedures  for  reassembly  of  the
5-14.
receiver/exciter  consist  of  replacement
Perform  the  procedures  in  para-
of five modules A1A1 thru A1A5 and rib-
graphs  5-7  thru  5-11  before
bon cable W1 (fig 5-2).
attempting  removal  of  W1.


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business