Click here to make tpub.com your Home Page

Page Title: Voice [Usb] Operation
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



TM 11-5820-509-12
operation is desired.
3-9. Teletype [Fsk] Operation
3-7. Voice [Usb] Operation
When the radio set is operated in the fsk mode, a
Place the front panel controls as follows:
teletypewriter and a converter-oscillator (both not
a. Verify that CW-FSK/VOICE switch (fig. 3-1) is at
supplied) must be obtained.  Converter-Oscillator CV-
VOICE.
786/PRC-47 (TM 11-5820-527-15) is recommended, or
b.  For transmission/reception, connect Handset H-
any other converter that uses 2425-MHz (mark) and 1875-
33G/PT to either AUDIO connector on the receiver-
MHz (space) frequencies. For the fsk mode, make the
transmitter front panel.  If only reception is desired,
following connections:
Dynamic Loudspeaker LS-166/U may be connected to the
a. Mount Adapter, Cable to Connector U-239/PRC-47
AUDIO connector.
(fig. 1-8) to either AUDIO connector on the receiver-
CAUTION
b.  Connect the output of the teletypewriter to the
During portable operation, use LO
converter-oscillator and the output of the converter-
power setting whenever possible to
oscillator to the wire connectors on Adapter U-239/PRC-
conserve battery power.
47.
c. Set XMTR PWR switch to LO for low power
c. Set the CW-FSK/VOICE switch (fig. 3-1) to CW-
operation, and to HI for high power operation.
FSK for both reception and transmission; set the switch to
d.  Press push-to-talk button on handset and wait 1
VOICE for reception only.
second before start of message. Whenever reception is
CAUTION
desired, release push-to-talk button.  Adjust VOLUME
control for comfortable listening level during receive
When battery is being used, use LO
periods.
power setting whenever possible to
e.  If the transmitting frequency must be changed,
conserve power.
adjust the frequency control knobs as in paragraph 3-6c,
d. Set XMTR PWR switch to LO for low power
repeat a through d above, and then perform paragraph
operation, and to HI for high power operation.
3-11. If a 50-ohm antenna is used, proceed to paragraph
e.  If the transmitting frequency must be changed,
adjust the frequency control knobs as in paragraph 3-6c.
Repeat a through e above, and then perform paragraph
3-8. Telegraph [Cw] Operation
3-11. If a 50-ohm antenna is used, proceed to paragraph
Adjust the front panel controls as follows:
a. Set the CW-FSK/VOICE switch (fig. 3-1) to CW-
3-10. Remote Control Operation
FSK for both reception and transmission; set the switch to
VOICE for reception only.
For remote control operation, proceed as follows:
b. Connect Cable Assembly, Special Purpose, Electrical
a. Connect Control Group AN/GRA-6 (TM 11-5038)
Branched CX-8396/PRC-47 to either AUDIO connector
to either AUDIO connector (fig. 3-11 on the receiver-
on receiver-transmitter front panel.
transmitter front panel.
c. Insert the connectors of Headset H-233/PRC-47 and
b.  Set all operating controls on the front panel in
Telegraph Key J-45 into the mating connectors in the
accordance with preceding instructions for mode of
branched end of Cable CX-8396/PRC-47.
operation desired. The AN/GRA-6 is then used to control
CAUTION During portable operation, use LO power
the power function only.
setting whenever possible to conserve battery power.
3-11. Tuning Power Amplifier
d.  Set XMTR PWR switch to LO for low power
When the transmitter portion of the receiver- is to be used,
operation, and to HI for high power operation.
the power amplifier and the antenna system must be
e. Adjust VOLUME control for a comfortable listening
resonated to the operating frequency to assure maximum
level during receive periods.
radiation of the rf signal and to prevent damage to the
f. If the transmitting frequency must be changed, adjust
power amplifier output circuits.
the frequency control knobs as in paragraph 3-6 c, repeat
CAUTION
a through e above, and then perform paragraph 3-11. If a
When the transmitting procedures direct the operator to
50-ohm antenna is used, proceed to paragraph 3-12.
this paragraph, be sure to perform each of the following
procedures in the sequence listed to assure proper loading.
a. Set XMTR PWR switch (fig. 3-1) to OFF.
3-4


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business