 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|  g e a r shaft (107), and washer (108)
the cam arm (84).
from rear plate (7).
Remove three screws (56) and
(23)
washers (57), and remove the three
1. Reassembly o f R e a r P l a t e ( f i g . 9 8 ) .
posts (58).
Note. In
this procedure,
Remove two retaining rings (59)
use
only
light-consist-
(24)
ency
grease.
from anchor shaft (55) and remove
anchor shaft from rear plate (7).
(1) Pack the 57-tooth gear (51) with
Loosen and remove clamps (60),
(25)
grease, place the gear on the rear
(61), (64), and (65), and couplers
plate (7) post, and secure with the
(62) and (63).
washer (50) and retaining ring (47).
(26)
Remove screw (66), washer (67),
Pack the gear set (46) with grease
(2)
and clamp assembly (68).
and mount on shaft on rear plate.
Remove screw (69), washer (70),
(27)
Place washer (45) on shaft and se-
and post (72).
cure with retaining ring (44).
(28)
Pack gear set (42) with grease,
Remove two screws (71) from two
(3)
place washer (43) on base of gear,
self-locking nuts (73) and remove
and slide the gear set (42) into posi-
switchplate (74).
tion under the 57-tooth gear (51)
Remove the 36-tooth gear (75) from
(29)
and the gear set (46).
rear plate (7).
Place washer (41) on gear assem-
Remove retaining ring (76), washer
(30)
(4)
bly (40) and carefully slide the gear
(77), and the 36-tooth gear (78) and
into the center of the gear set (42).
the 72-tooth gear (79) from rear
Check for proper gear mesh.
plate (7).
Lightly oil the hub of the 29-tooth
Remove cam shaft (80), the 36-
(31)
(5)
gear (90), mount on shaft of rear
tooth gear (81), gear frame assem-
plate, place washer (89) on shaft,
bly (82), and the 36-tooth gear (83)
and secure with retaining ring (88).
from rear plate (7).
Lightly oil the hubs of the 72-tooth
Remove cam arm (84), gear frame
(6)
(32)
gear (79) and the 36-tooth gear (78)
assembly (85), gear set (86), and
and mount on the shaft on the rear
washer (87) from rear plate (7).
p l a t e . Place washer (77) on the
(33)
Remove retaining ring (88), washer
shaft and secure with retaining ring
(89), and the 29-tooth gear (90)
(76).
from rear plate (7).
Lightly oil hub of the 96-tooth gear
(7)
(34)
Remove retaining rings (95) and
(36), place gear and washer (35) on
(96) from the shaft of drive shaft
s h a f t , and secure with retaining
(101).
ring (34),
(35)
Slide the 84-tooth gear (97) and
Lightly oil hub of the 54-tooth gear
the 76-tooth gear (100) apart and
(8)
(39), place gear and washer (38) on
remove the loop of the spring (99)
s h a f t , and secure with retaining
from the post on the 84-tooth gear
(97).
ring (37).
Place clamp (28) upon base of gear
Remove retaining ring (98) from
(36)
(9)
the post on the 76-tooth gear (100)
assembly (26), slide the gear as-
and remove the loop of the spring
sembly into position on shaft (27),
(99).
mount retaining ring (30), washer
(29), and tighten clamp (28). Place
Remove drive shaft (101) from rear
(37)
a thin coating of low-temperature
plate (7) and remove washer (105),
oil on the bronze bearing and insert
gear set (104) and the 76-tooth gear
t h e shaft (27) through the rear
(103) and spring (102).
plate. Secure the shaft (27) with
Remove retaining ring (91), washer
(38)
clamp (2) and coupler (1).
(92), and the two 57-tooth gears (93)
P l a c e retaining ring (59) on the
(10)
and (94) from rear plate (7).
c e n t e r m o s t slot of anchor shaft
Remove retaining ring (106), idler
(39)
152
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals