Click here to make tpub.com your Home Page

Page Title: Reassembly of Rear Plate-continued
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



drive shaft (101).
(55),  insert
the
anchor
shaft
(21) Mount the 84-tooth gear (97) on
through hole in rear plate, and se-
drive shaft (101), grasp the loop of
c u r e with second retaining ring
spring (99) with pliers, and mount
(59).
on post of gear (97). Slide gears
Mount clamp assembly (68) on rear
(11)
(100) and (97) together on drive
plate;  position  and  secure  with
shaft (101) and secure with retain-
washer (67) and screw (66).
ing rings (95) and (96).
M o u n t switchplate (74) on rear
(12)
plate and secure with self-locking
N o t e . Spring (99) is wound to a speci-
nuts (73) and screws (71).
f i e d torque of 2 inch-pounds by turning
Mount post (72) under clamp as-
(13)
gear (97) counterclockwise, as viewed from
sembly (68) and secure with washer
t h e front of the rear p l a t e . T h e t o r q u e
(70) and screw (69).
loading  is  read  at  coupler  (62),  using
Place a thin coating of oil (OGP) on
(14)
t o r q u e meter and adapter shaft assembly
the bronze bearing and place wash-
listed in b above. If the loading is not cor-
rect, remove retaining ring (95), disengage
er (105) and gear set (104) imposi-
the 84-tooth gear (97) from gear frame as-
tion on the bearing.
sembly (85), tighten or loosen spring load-
Place washer (108) on idler gear
(15)
ing by rotating the 84-tooth gear (97) coun-
shaft (107). Place a thin coating of
terclockwise or clockwise, engage gear
oil (OGP) on the bronze bearing and
(97) with gear frame assembly (85), and re-
slide idler shaft (107) into bearing
p l a c e retaining ring (95). Recheck for 2
on rear plate and secure with re-
inch-pounds of torque on coupler (62).
taining ring (106).
(22) Mount the three posts (58) on the
Lightly oil the hub of the 57-tooth
(16)
holes in the rear plate (7) and se-
gear (94) and mount on the shaft.
cure with washers (57) and screws
Lightly oil the hub of the 57-tooth
(56) .
gear (93) and mount on the 57-tooth
(23) Place washer (33) on gear shaft as-
gear (94). Place washer (92) on the
sembly (32), lightly oil the bronze
shaft and secure with retaining ring
bearing in the rear plate with low-
(91).
t e m p e r a t u r e oil, and insert the
Mount spring (102) on the gear of
(17)
shaft assembly (32) through the
drive shaft (101), place the 76-tooth
rear plate. Replace washer (31).
gear (103) on drive shaft (101), and
Secure with clamp (4) and cou-
insert opposite end of spring (102)
pler (3).
in the 76-tooth gear (103). Rotate
(24) Lightly oil hub of the 36-tooth gear
drive shaft (101) and the 76-tooth
(24) and place on gear shaft (25).
gear (103) to close the spring. In-
Place was her (23) on gear shaft
sert the gear loading rod ( b above)
(25), oil bronze bearing on gear
in the holes provided to maintain
plate (10) with oil (OGP) and insert
the loading until the front and rear
gear shaft through bearing. Secure
plates are reassembled.
gear shaft (25) with clamp (52) and
(18)
Insert the drive shaft (101) through
coupler (53).
the hub of the gear set (104) and the
(25) Mount gear (12) on gear plate (10)
bronze bearing, and carefully mesh
and secure with retaining ring (11).
the 76-tooth gear (103) with gear
(26) Lightly oil bronze bearing with oil
set (104) and idler gear shaft (107).
( O G P ) , insert cam (48) through
Secure with clamp (60) and coupler
rear plate, and secure with clamp
(63) on rear of rear plate.
(49) .
(19)
Mount spring (99) upon the small
(27) Lightly oil the bronze bearing with
post of the 76-tooth gear (100) and
oil (OGP), insert the shaft of the
s e c u r e the spring with retaining
36-tooth gear (75) through the rear
ring (98).
plate, and secure clamp (65).
(20)
Mount the 76-tooth gear (100) on
153


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business