Special Information - TM-11-5895-532-34P-30005

TM 11-5895-532-34P-3

(3) Recoverability code. Recoverability codes are

the illustration figure, which is prepared for a functional

assigned to support items to indicate the disposition

group, subfunctional group, or an assembly.

action on serviceable items. The recoverability code is

4. Special Information

entered in the fifth position of the Uniform SMR Code

a. Usable on codes are shown in the description

format as follows:

column. Uncoded items are applicable to all models.

Recoverability

Identification of the useable on codes used in this

Codes

Definition

publication are:

Z-Nonreparable item. When unserviceable, condemn

Code

Used on

and dispose at the level indicated in position 3.

ASJ

ANITPX46(V)1

H--Reparable item. When uneconomically reparable,

CLD

ANITPX46(V)2

condemn and dispose at the general support level.

CLE

AN/TPX46(V)3

D--Reparable item. When beyond lower level repair

CLF

AN/TPX46(V)4

capability, return to depot. Condemnation and

CLG

ANITPX46(V)6

disposal not authorized below depot level.

The

following publications pertain to the

L-Reparable item. Repair, condemnation, and disposal

CP925/TPX46(V) and its components:

not authorized below depot/specialized repair

TM 11-5895-532-34-3, Interrogator Sets

activity level.

AN/TPX46(V)1, 2, 3, 4, and 6 (Signal

c. National Stock Number. Indicates the National

Processor CP9251TPX46(V))

stock number assigned to the item and will be used for

5. How to Locate Repair Parts

requisitioning purposes.

a, When National stock number or part number is

d. Part Number. Indicates the primary number used

unknown.

by the manufacturer (individual, company, firm,

(1) First. Using the table of contents, determine

corporation, or Government activity), which controls the

the functional group within which the item belongs. This

design and characteristics of the item by means of its

is necessary since illustrations are prepared for

engineering drawings, specifications, standards, and

functional groups and listings are divided into the same

inspection requirements to identify an item or range of

groups.

items.

(2) Second. Find the illustration covering the

NOTE

functional group to which the item belongs.

When a stock numbered item is

(3) Third. Identify the item on the illustration and

requisitioned, the repair part received may

note the illustration figure and item number of the item.

have a different part number than the part

(4) Fourth. Using the Repair Parts Listing, find the

being replaced.

figure and item number noted on the illustration.

e. Federal Supply Code for Manufacturer (FSCM).

b. When National stock number or part number is

The FSCM is a 5-digit numeric code listed in SB70841/42

known.

which is used to identify the manufacturer, distributor, or

(1) First. Using the Index of National Stock

Government agency, etc.

Numbers and Part Numbers, find the pertinent National

f. Description., Indicates the Federal item name and,

stock number or part number. This index is in NIIN

if required, a minimum description to identify the item.

sequence followed by a list of part numbers in

g. Unit of measure (U/M). Indicates the standard of

alphanumeric sequence, cross-referenced to the

the basic quantity of the listed item as used in performing

illustration figure number and item number.

the actual maintenance function.

This measure is

(2) Second. After finding the figure and item

expressed by a two-character alphabetical abbreviation

number, locate the figure and item number in the repair

(e.g., ea, in, pr, etc.). When the unit of measure differs

parts list.

from the unit of issue, the lowest unit of issue that will

6. Abbreviations

satisfy the required units of measure will be requisitioned.

Not applicable.

h. Quantity Incorporated in Unit. Indicates the

quantity of the item used in the breakout shown on

(Next printed page is 4.1)