Section I. INTRODUCTION - TM-11-5821-261-35P0012

TM 11-5821-261-35P

SECTION I.

INTRODUCTION

Code

Explanation

1. Scope

P2-Repair parts which are procured and stocked

This manual lists repair parts, special tools, and

for insurance purposes because the combat

or military essentiality of the end item dic-

test equipment required for the performance of

tates that a minimum quantity be available in

direct support, general support, and depot main-

the supply system.

tenance of the Radio Set AN/ARC-116.

P9-Assigned to items which are NSA design con-

trolled: unique repair parts, special tools,

test, measuring and diagnostic equipment,

2. General

which are stocked and supplied by the Army

This Repair Parts and Special Tools List is di-

COMSEC logistic system, and which are not

vided into the following sections:

subject to the provisions of AR 380-41.

P10-Assigned to items which are NSA design con-

a. Repair Parts--Section II. A list of repair

trolled: special tools, test measuring and

parts authorized for the performance of mainte-

diagnostic equipment for COMSEC support,

nance at the direct support, general support, and

which are accountable under the provisions

depot levels.

of AR 380-41, and which are stocked and

supplied by the Army COMSEC logistic Sys-

b. Special Tools, Test and Support Equip-

tem.

ment--Section III. A list of special tools, test and

M--Repair parts which are not procured or stocked

support equipment authorized for the perform-

but are to be manufactured in indicated main-

ance of maintenance at the direct support, gen-

tenance levels.

eral support, and depot levels.

A--Assemblies which are not procured or stocked

as such, but are made up of two or more

c. Federal Stock Number and Reference Num-

units. Such component units carry individual

ber Index--Section IV. A list of Federal stock

stock numbers and descriptions, are procured

numbers in ascending numerical sequence fol-

and stocked separately and can be assembled

lowed by a list of reference numbers in ascending

to form the required assembly at indicated

maintenance categories.

alpha-numeric sequence, cross-referenced to the

X--Parts and assemblies which are not procured or

illustration figure number and reference desig-

stocked and the mortality of which normally

nation.

is below that of the applicable end item or

d. Reference Designation Index--Section V. A

component. The failure of such part or as-

sembly should result in retirement of the end

list of reference designations in ascending alpha-

item from the supply system,

numeric sequence cross-referenced to page num-

X1--Repair parts which are not procured or stocked.

ber.

The requirement for such items will be filled

by use of the next higher assembly or com-

ponent.

3. Explanation of Columns

X2--Repair parts which are not stocked. The indi-

The following provides an explanation of columns

cated maintenance category requiring such

repair parts will attempt to obtain same

in the tabular lists in Sections II and III.

will

requirements

through cannibalization,

a. Source, Maintenance, and Recoverability

be requisitioned, with accompanying justifi-

Codes (SMR), Column 1:

cation, through normal supply channels.

(1) Source code, indicates the selection

G--Major assemblies that are procured with PEMA

funds for initial issue only as exchange as-

status and source for the listed item. For expla-

semblies at DSU and GSU level. These as-

nation of split source codes see paragraph 4.

semblies will not be stocked above DS and

Source codes used are:

GS level or returned to depot supply level.

Code

Explanation

Note. Source coding of selected hardware items has been

excluded. These item are authorized "as required."

P--Repair parts which are stocked in or supplied

(2) Maintenance code, indicates the lowest

from the GSA/ DSA, or Army Supply Sys-

category of maintenance authorized to install the

tem and authorized for use at indicated main-

listed item. The maintenance level codes are:

tenance categories.