Click here to make tpub.com your Home Page

Page Title: Section II. Disassembly and Reassembly
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



TM
11-5820-919-40-1
SECTION
II
DISASSEMBLY
AND
REASSEMBLY
AMPLIFIER/COUPLER
DISASSEMBLY
RIBBON
CABLE
A2W1
REMOVAL.
Procedures  for  disassembly  of  the
6-6.
NOTE
amplifier/coupler  (A2)  consist  of  remov-
ing the two modules, A2A1 and A2A2, rib-
Remove  power  amplifier  and
bon  cable  A2W1,  antenna  mount,  BNC  con-
antenna  tuner  before  attempt-
nector  A2J1,  and  antenna  select  (A N T
ing  removal  of  ribbon  cable
SEL)  switch  A2S1.
A2W1 .
POWER
AMPLIFIER
A2A1
REMOVAL.
1.
Locate  connector  receptacle  A2W1P1
(13) on  the  side  of  amplifier/coupler
1.
Place  the  amplifier/coupler  so
housing  (4).
that the cover assembly (10) is on top
and  front  face  reads  up-side  down.
2.
Remove  the  mounting  screws  of
multipin  connector  A2W1J3  (12)  which  are
Remove  the  cover  assembly  (10)
by
2.
located on the opposite side of the
loosening  the  8  captive  screws  (9).
amplifier/coupler  unit  just  below  multi-
pin  connector  A2W1J2  (49).
Disconnect  the  rf  cables  A1J1,
3.
3.
Remove screw and nut that mount
A1J2  (5)  from  the  power  amplifier  module
terminal  E1  to  amplifier/coupler  housing
assembly  (11).
(4)  adjacent  to  multipin  connector
A2W1J3  (12).
4.
Loosen  the  4  captive  (Phillips
head)  screws  (8)  that  connect  the  power
4.
Remove  the  mounting  screws  (44)
amplifier  module  assembly  (11)  to  the
for  multipin  connector  A2W1J2  (49),
amplifier/coupler
housing
(4).
which  are  located  on  the  opposite  side
of  amplifier/coupler  unit,  just  above
Grasp the wire handle on the mod-
5.
multipin  connector  A2W1J3  (12).
ule and pull gently upward so that the
5.
Place  amplifier/coupler  so  that
module  is  removed.
the  battery  connector  P1  (37)  faces
upward  and  remove  the  2  mounting  screws
ANTENNA
TUNER
A2A2
REMOVAL.
(38)  with  associated  washers.
Place  the  amplifier/coupler  so
1.
6.
Remove screw and nut that mount
that the cover assembly (1) is on top.
terminal  E1  (48)  to  amplifier/coupler
housing (4) at the base of multipin
Remove  the  cover  assembly  (1)  by
2.
connector  A2W1J2  (19)  adjacent  to  the
loosening  the  8  captive  screws  (2).
capacitors  (39).
Disconnect  the  rf  cable  A2J1  (16)
3.
CAUTION
from  the  antenna  tuner  module  assembly
(14).
Use  extreme  care  when  removing
or  replacing  ribbon  cables.
Loosen the 4 captive screws (3)
4.
Creasing  or  severe  bending
that connect the module to the
will  damage  ribbon  cables
amplifier/coupler
housing
(4).
internally.
5.
Grasp  the  module  and  pull  gently
7.
Grasp  ribbon  cable  support  (45)
upward so that the module is removed.
and  ribbon  cable  assembly  (47)  and


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business