• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Section X. EPLRS CABLING
Section X. EPLRS CABLING - Continued

Sincgars An/Vrc-88F, An/Vrc-89F, An/Vrc-90F, An/Vrc-91F, An/Vrc-92F Force Xxi Battle Command, Brigade-And-Below (Fbcb2) An/Uyk-128(V) Defense Advanced Gps Receiver (Dagr) An/Psn-13 Vehicular Intercommunication Set (Vis) An/Vic-3(V)20 Blue Force Tracking (Bft) Enhanced Position Location Reporting System (Eplrs) An/Vqz-2(V) For Vehicle Truck, Utility: Expanded Capacity, Enhanced, Iap/Armor Ready, M1152A1 (2320-01-540-2007) Page Navigation
  63    64    65    66    67  68  69    70    71    72    73  
img
TB 9-2320-387-35-7
10-2. Remove two countersunk screws (3) from interface plate (14).
10-3. Remove capscrew (5) from wheelhouse mount bracket (12).
NOTE
If EPLRS unit is available, connect power cable, INC-EPUU cable,
antenna cable, and ground leads to EPLRS unit. Otherwise route
cables to vicinity of EPLRS mount.
10-4. Route EPLRS power cable (10), INC-EPUU cable (8), and antenna cable (16) along interface
plate (14), left side wheelhouse (15), left rear seat/utility area (22), and along tunnel (25).
10-5. Route EPLRS power cable (10) and INC-EPUU cable (8) through hole (1) and into cab of
vehicle (26).
10-6. Secure three cables (8), (10), and (16) to interface plate (14) with two clamps (9), capscrews (4),
lockwashers (6), washers (7), and washers (11).
10-7. Secure three cables (8), (10), and (16) to interface plate (14) with clamp (9), capscrew (5),
lockwasher (6), washer (7), and washer (11).
10-8. Secure three cables (8), (10), and (16) to left side wheelhouse (15) with clamp (9), existing
capscrew (17), lockwasher (6), and washer (7).
10-9. Locate, mark, and drill 0.147-in. diameter hole (19) in wheelhouse (15).
10-10. Secure three cables (8), (10), and (16) to wheelhouse (15) with clamp (18) and self-tapping screw (23).
10-11. Secure three cables (8), (10), and (16) along edge in left rear seat/utility area (22) with two
capscrews (20), four washers (7), two clamps (9), lockwashers (6), and nuts (21).
10-12. Locate, mark, and drill three 0.147-in. diameter holes (24) in tunnel (25).
10-13. Secure three cables (8), (10), and (16) to tunnel (25) with three clamps (18) and self-tapping screws (23).
10-14. Split grommet (27) and install on EPLRS power cable (10) and INC-EPUU cable (8).
10-15. Install grommet (27) in hole (1).
10-16. Route EPLRS antenna cable (16) towards overhead mount.
4.
CAPSCREW B1821BH025C200N QTY. 2
3
4
3
4
5
5.
CAPSCREW B1821BH025C125N QTY. 1
6
6.
LOCKWASHER MS35338-44 QTY. 3
6
7.
WASHER 9414920 QTY. 3
7
7
8.
INC-EPUU CABLE A3279383-3 QTY. 1
8
9.
CLAMP MS21333-105 QTY. 3
9
10.
EPLRS POWER CABLE A3004939 QTY. 1
11.
WASHER MS51412-23 QTY. 3
16.
EPLRS ANTENNA CABLE SM-C-911480 QTY. 1
16
10
~
11
12
13
~
11
14
15
Figure 5-67.
5-58


Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved.