Quantcast REPLACEMENT OF BATTERY TRAY CIRCUIT CARD ASSEMBLY (12A1A1) (cont)

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF BATTERY TRAY CIRCUIT CARD ASSEMBLY (12A1A1) (cont)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  BATTERY  TRAY  GASKET (cont)
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  CONNECTOR  BOARD  CIRCUIT  CARD  ASSEMBLY  (12A1A2) AND  P1  CONNECTOR


TM 11-5820-890-30-5 15-22. REPLACEMENT OF BATTERY TRAY CIRCUIT CARD ASSEMBLY (12A1A1). Tools: Cross  tip  screwdriver Soldering  kit Heat sink Long  nose  pliers Soldering  aid Expendable  Supplies: Solder Alcohol Cotton  swabs References: Paragraph  15-20  for  removal  and  installation  of  mounting  plate  assembly. Paragraph  15-35  for  removal  and  installation  of  threaded  screw  inserts. ITEM ACTION REMARKS REMOVAL a.  Mounting  plate assembly  (2) b.  Battery  tray subassembly  (1) c.   A1   battery   tray   CCA wires  (2) d.   17   E-terminals e.   Six   screws,   flat   washers, and  Iockwashers  (7) f.   A1   battery   tray   CCA   (8) INSTALLATION g.  A1  battery  tray  CCA  (8) h.  Six  screws,  flat  washers, and  Iockwashers  (7) i. A1  battery  tray  CCA  (8) j. Mounting  plate assembly  (2) Remove  and  retain. Set  upside  down  on  work  surface  with left  side  toward  you. Tag  the  location  of  each  wire  soldered to  17  E-terminals  on  A1  battery  tray CCA.  See  figure  15-6. Use  long  nose  pliers  and  soldering  equip- ment.  Desolder  and  remove  20  tagged wires  from  17  E-terminals. See  figure  15-5.  Use  cross  tip  screw- driver.  Remove  and  inspect  six  screws, flat  washers,  and  Iockwashers  securing A1  battery  tray  CCA  (8)  to  chassis. If   damaged,   obtain   replacement, Remove  and  discard. Obtain  replacement  A1  battery  tray  CCA and  place  it  on  the  chassis. Use  cross  tip  screwdriver.  Install  six retained  screws,  flat  washers,  and Iockwashers  securing  A1  battery  tray CCA  (8)  to  chassis. Use  long  nose  pliers  and  soldering  equip- ment.  Attach  and  solder  20  tagged  wires to  17  E-terminals  on  A1  battery  tray  CCA, and  remove  wire  tags.  See  figure  15-6. Install  retained  mounting  plate  assembly on  battery  tray  subassembly  (1). Refer  to  paragraph  15-20 for  removal  of  mounting plate  assembly. These  were  removed  in step  e. Before  and  after  soldering, clean  wires  and  E-terminals with  alcohol  and  cotton swabs. Refer  to  paragraph  15-20 for  installation  of  mounting plate  assembly. 15-24


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business