Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF POWER SUPPLY ADAPTER CHASSIS ASSEMBLY. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 



14-40.  REPLACEMENT TM 11-5820-890-30-5 OF  POWER  SUPPLY  ADAPTER  CHASSIS  ASSEMBLY.  Continued ITEM ACTION REMARKS INSTALLATION  Continued bu. bv. O-ring Hex nut, switch plate,  and  lock  ring bw.  Circuit  breaker  (7) wires bx. by. Hex  nut  and bz. ca. cb. cc. cd. two  hex  nuts, ce. O-ring lockwasher Lamp  holder  (6) wires Lamp Light  lens O-rings flat  washers,  Iockwashers, and  nylon  washers Binding  post  (5) wires Apply  silicone  compound  to  o-ring on  retained  CB1  circuit  breaker  (7) See  figure  14-9. Use  adjustable  wrench.  Insert  retained circuit  breaker  in  chassis  with  proper orientation.  Install  and  hand  tighten retained  hex  nut,  switch  plate,  and lock  ring  securing  circuit  breaker  on chassis.  Use  torque  wrench.  Torque to  20  in-lb. Use  soldering  kit,  soldering  aid,  heat Before  and  after  soldering, sink,  and  needle  nose  pliers.  Install  and clean  wires  and  terminals solder  tagged  wires  to  correct  terminals with  alcohol  and  cotton on  the  circuit  breaker,  and  remove swabs. the  wire  tags. Apply  silicone  compound  to  o-ring on  retained  DS1  lamp  holder  (6). Use  9/16  inch  wrench.  Install  and  hand tighten  retained  hex  nut  and  replacement Iockwasher  securing  lamp  holder  on  chassis. Use  torque  wrench.  Torque  to  30  in-lb. Use  soldering  kit,  soldering  aid,  and Before  and  after  soldering, heat  sink.  Solder  tagged  wires  to clean  wires  and  terminals correct  terminals  on  the  lamp  holder, with  alcohol  and  cotton and  remove  the  wire  tags. swabs. Install  retained  lamp  in  lamp  holder. Install  and  tighten  retained  light  lens on  lamp  holder. Apply  silicone  compound  to  o-rings  on retained  E1  and  E2  binding  posts  (5). Use  5/16  inch  wrench.  Install  and  hand tighten  two  retained  hex  nuts,  flat  washers, nylon  washers,  and  replacement  Iockwashers securing  binding  posts  on  chassis.  Use torque  wrench.  Torque  to  6  in-lb. Use  soldering  kit,  soldering  aid,  and  heat Before  and  after  soldering, sink.  Solder  tagged  wires  to  correct clean  wires  and  terminals terminals  on  rear  of  the  binding  posts, with  alcohol  and  cotton and  remove  the  wire  tags. swabs. 14-73


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business