Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: OPERATIONAL CHECK (cont)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 



TM 11-5820-890-30-5 Section  IV.  MAINTENANCE Subject General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operational Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repair Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacement of Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . Replacement of PA Mount Chassis . . . . . . . . . . . . . . . . . . . . . . Lamp DS1 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13.  GENERAL. PROCEDURES Para Page . . . . . . . . . . . . . . . . . . . . . .   9-13 9-16 . . . . . . . . . . . . . . . . . . . . . .   9-14 9-16 . . . . . . . . . . . . . . . . . . . . . .   9-15 9-16 . . . . . . . . . . . . . . . . . . . . . .   9-16 9-19 . . . . . . . . . . . . . . . . . . . . . .   9-17 9-20 . . . . . . . . . . . . . . . . . . . This  section  includes  the  operational  check  and  the  repair  procedures.  The  operational . .   9-18 9-20 check  is  used  to  verify the operation of a repaired PA mount. It is also used to verify the symptom of a faulty PA mount. It will identify the troubleshooting chart to be used. When a bad module is identified, replace it using the procedure in this section. 9-14.  OPERATIONAL  CHECK. Perform  the  operational  check  found  in  paragraph  9-8  to  verify  the  proper 9-15.  REPAIR  PROCEDURES. The  following  instructions  apply  to  all  repair  tasks  unless  otherwise  noted  in parts  location. a. Begin  procedure  with  PA  mount  switch  CB1  set  to  OFF. b. Disconnect  any  external  cables  connected  to  PA  mount. operation  of  the  PA  mount. the  procedure,  See  figure c. Inspect  PA  mount.  Replace  PA  mount  chassis  if  it  is  physically  damaged,  such  as  with  a connector. d. PA  mount  must  be  tested  after  replacement  of  a  module.  See  paragraph  9-8  for  operational CAUTION 9-4  for broken check. Steps marked with          must be performed exactly as written. They are critical in maintaining the nuclear hardness of the PA mount. Seals must not be damaged. All screws must be torqued to  the  limits  specified  in  Appendix  B. 9-16


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business