Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF POWER CONTROL CHASSIS O-RING GASKET. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 



TM 11-5820-890-30-5 4-39. REPLACEMENT OF POWER CONTROL CHASSIS O-RING GASKET. Continued ITEM ACTION REMARKS REMOVAL  Continued e.  Five  screws  (7  and  8) f.   Two   screws   (5) g.   Bottom   cover   (13) h.   Connector   P1   (12) i. Four  screws  (40) j. Wire  connections  on connector  P1  (12) k.   Side   panel   (6)   and power  control l. O-ring   gasket INSTALLATION m.   O-ring   gasket chassis  (4) (4) (4) n.  Side  panel  (6)  and power  control  chassis  (4) o.   Wire   connections   on connector  P1  (12) Using  cross  tip  screwdriver,  remove  and retain  five  screws  (7  and  8)  securing  top shelf  (9)  to  mounting  rail  (10)  on  side panel  (6)  of  power  control  chassis  (4). Using  cross  tip  screwdriver,  remove  and retain  two  screws  (5)  securing  side  panel (6)  of  power  control  chassis  (4)  to  power supply  chassis  (15). Remove  and  retain. Using  flat  tip  screwdriver,  remove  and retain  four  screws  (14)  securing  connector P1  to  power  supply  chassis  (6).  Move connector  P1  aside. Using  cross  tip  screwdriver,  remove  and retain  four  screws  (40)  securing  rear  of power  control  chassis  (4)  to  power  supply chassis   (15). Using  soldering  kit,  tag  and  desolder  the following  wires  from  connector  P1  (12) leading  into  power  control  chassis. P1  CONNECTOR  PIN COLOR B YELLOW c WHITE E BROWN Remove  from  mounting  adapter power  supply  chassis  (15). Inspect,  remove,  and  replace  as Clean  case  channel  of  all  debris. required. Install  in  channel  on  power  control chassis  case  and  secure  with cyanoacrylate   adhesive. Position  side  panel  (6)  and  power  control chassis  (4)  to  power  supply  chassis  (15). Using  cross  tip  screwdriver  install  four retained  screws  (4)  securing  rear  of  power control  chassis  (4)  to  the  power  supply chassis   (15). Using  soldering  kit,  solder  tagged  wires to  correct  pins  of  connector  P1  (12). See  figure  4-11. See  figure  4-11. See  figure  4-10. Refer  to  paragraph  4-40  for removal   procedures. See  figure  4-13. See  figure  4-11. See  figure  4-13. See  figure  4-11. See  figure  4-12. Apply  silicone  compound to   o-ring   gasket   before installation. These  were  removed  in step  k.  See  figure  4-11. These  were  removed  in step  j.  See  figure  4-13. 4-138


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business