Click here to make tpub.com your Home Page

Page Title: Section IV. MAINTENANCE
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



TM 11-5820-873-34
Section IV. MAINTENANCE
(3) Reinstall Regulator Assembly 1A6A1 (22) into
4-7. General
connector 1A6XA1 (18).
General support maintenance of the AN/URC-92 is limited
(4)  Position  rubber  support  (23)  between
to the replacement and/or repair of wiring and connectors,
Regulator Assembly 1A6A1 (22) and Power Supply 1A6.
circuit card replacement and/or repair and the procedures
outlined in this manual.
CAUTION
4-8. Power Supply 1A6
Positive terminals of capacitors 1A6A1C5
and 1A6A1C9 must match positive markings
a. Removal.
on Regulator Board.
(1) Remove transceiver top cover.
(5)  Position  capacitors  1A6A1C5  (9)  and
(2) Remove transceiver bottom cover.
1A6A1C9 (10) and secure each with two mounting screws
(3) Remove four screws holding Synthesizer 1A4
(4) and washers (5) through Regulator Assembly 1A6A1
protective cover and remove protective cover.
(22).
(4) Extract Spectrum Generator 1A4A1, Low Digit
(6) Reinstall two mounting screws (21) and
Generator 1A4A2, Translator 1A4A3, and VHF Divider
washers (19 & 20) in connector 1A6XA1 (18).
1A4A4 circuit card assemblies.
(7) Reinstall two standoffs (3) on Regulator
(5) Remove two screws and washers (16) holding
Assembly 1A6A1 (22).
Power Supply 1A6 to Synthesizer 1A4.
(8)  Position  Regulator  Assembly  1A6A1
(6) Remove one screw and washer (15) mounting
protective cover (2) and secure with four screws (1).
power supply to chassis assembly.
(9) Position rear panel in place and secure with
(7) Remove two screws (17) mounting power
six mounting screws to left and right side panels.
supply to rear panel.
(10) Reinstall two power supply mounting screws
(8) Remove six screws mounting rear panel to
(17) through rear panel.
right and left side panels and pull away rear panel
(11) Reinstall one power supply mounting screw
(9) Remove four screws (1) from Regulator
(15) through chassis assembly.
Assembly 1A6A1 protective cover (2) and remove cover.
(12) Reinstall two power supply mounting screws
(10) Remove two standoffs (3) from Regulator
(16) through Synthesizer 1A4.
Assembly 1A6A1 (25).
CAUTION
(11) Remove four screws (4) and washers (5)
When reinstalling Spectrum Generator, Low
mounting capacitors 1A6AIC5 (9) and 1A6A1C9 (10) and
Digit Generator, Translator, and VHF Divider
remove capacitors.
circuit card assemblies, component side
(12) Remove two mounting screws (21) and
must face rear of transceiver.
washers (19 & 20) from connector 1A6XA1 (18).
(13) Reinstall Spectrum Generator 1A4A1, Low
(13) Extract Regulator Assembly 1A6A1 (22) from
Digit Generator 1A4A2, Translator 1A4A3, and VHF
connector 1A6XA1 (18).
Divider 1A4A4 circuit card assemblies.
(14) Remove two mounting screws (11) and
(14) Position Synthesizer 1A4 protective cover in
washers (12 & 13) from terminal board 1A6TB1 (14).
place and secure with four mounting screws.
NOTE
(15) Reinstall transceiver bottom cover.
Reposition terminal board 1A6TB1 to access
(16) Reinstall transceiver top cover.
screws mounting Power Supply 1A6 to
4-9. Power Transformer (1A6T1)
transformer 1A6T1.
(15) Remove four screws (8) and washers (7)
a. Removal.
mounting Power Supply 1A6 to Power Transformer 1A6T1
(1) Remove transceiver top cover
(6) and remove Power Supply.
(2) Remove transceiver bottom cover.
b. Replacement.
(3) Remove four screws (1) from Regulator
(1) Position Power Supply 1A6 in place and
Assembly 1A6A1 protective cover (2) and remove cover.
secure with four screws (8) and washers (7) to Power
(4) Remove two standoffs (3) from Regulator
Transformer 1A6 T1 (6).
Assembly 1A6A1 (22).
(2) Position terminal board 1A6TB1 (14) in place
(5) Remove two screws (4) and washers (5) from
and secure with two mounting screws (11) and washers
capacitor 1A6A1C5 (9) and remove capacitor.
(12 & 13).
(6) Remove two screws (4) and washers (5) from
CAUTION
capacitor 1A6A1C9 (12) and remove capacitor.
Component side of Regulator Assembly
(7) Remove two mounting screws (21) and
must face top of transceiver.
washers (19 & 20) from connector 1A6XA1 (21).
4-32


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business