|
| TM 11-5820-785-24P
SECTION I
INTRODUCTION
NOTE
1. Scope
This manual lists spares and repair parts; special tools;
Cannibalization or salvage may be used as a
special test, measurement, and diagnostic equipment
source of supply for any items source coded
(TMDE), and other special support equipment required for
above except those coded XA and aircraft
performance of organizational, direct support, and general
support items as restricted by AR 700-42.
support maintenance of the AN/FRC-80(V)1, AN/FRC-80(V)2,
and AN/FRC-80(V)3. It authorizes the requisitioning and
(2) Maintenance code.
Maintenance codes are
issue of spares and repair parts as indicated by the source
assigned to indicate the levels of maintenance authorized to
and maintenance codes.
USE and REPAIR support items. The maintenance codes are
entered in the third and fourth positions of the Uniform SMR
2. General
Code format as follows:
This Repair Parts and Special Tools List is divided into the
(a) The maintenance code entered in the third
following sections:
position will indicate the lowest maintenance level authorized
to remove, replace, and use the support item. The
parts authorized for use in the performance of maintenance.
maintenance code entered in the third position will indicate
The list also includes parts which must be removed for
one of the following levels of maintenance:
replacement of the authorized parts. Parts lists are composed
of functional groups in numeric sequence, with the parts in
Code
Application/Explanation
O --Support item is removed, replaced, used at the
each group listed in figure and item number sequence.
organizational level.
b. Section III. Special Tools List. Not applicable.
F --Support item is removed, replaced, used at the direct
c. Section IV. National Stock Number and Part Number
support level.
Index. A list, in National item identification number (NIIN)
H --Support item is removed, replaced, used at the general
sequence, of all National stock numbers (NSN) appearing in
support level.
the listings, followed by a list, in alphameric sequence, of all
part numbers appearing in the listings. National stock
(b) The maintenance code entered in the fourth
numbers and part numbers are cross referenced to each
position indicates whether the item is to be repaired and
illustration figure and item number appearance.
identifies the lowest maintenance level with the capability to
perform complete repair (i.e., all authorized maintenance
3.
Explanation of Columns
functions). This position will contain one of the following
a. Illustration. This column is divided as follows:
maintenance codes:
(1) Figure number. Indicates the figure number of
the illustration on which the item is shown.
Code
Application/Explanation
(2) Item number. The number used to identify
F --The lowest maintenance level capable of complete repair
item called out in the illustration.
of the support item is the direct support level.
b. Source, Maintenance, and Recoverability (SMR)
H --The lowest maintenance level capable of complete repair
Codes.
of the support item is the general support level.
(1) Source code. Source codes indicate the manner
D --The lowest maintenance level capable of complete repair
of acquiring support items for maintenance, repair, or
of the support item is the depot level.
overhaul of end items. Source codes are entered in the first
Z --Nonreparable. No repair is authorized.
and second positions of the Uniform SMR Code format as
follows:
(3) Recoverability code. Recoverability codes are
assigned to support items to indicate the disposition action on
Code
Definition
unserviceable items. The recoverability code is entered in the
PA --Item procured and stocked for anticipated or known
fifth position of the Uniform SMR Code format as follows:
usage.
PD --Support item, excluding support equipment, procured
Recoverability
for initial issue or outfitting and stocked only for
codes
Definition
subsequent or additional initial issues or outfittings.
Z --Nonreparable item. When unserviceable, condemn and
Not subject to automatic replenishment.
dispose at the level indicated in position 3.
XD --A support item that is not stocked. When required, item
F --Reparable item.
When uneconomically reparable,
will be procured through normal supply channels.
condemn and dispose at the direct support level.
H --Reparable item.
When uneconomically reparable,
condemn and dispose at the general support level.
1
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |