|
| TM 11-5820-615-24P
that no specific quantity is applicable, (e.g., shims,
Code
Application/Explanation
spacers, etc).
Z ----- Nonreparable. No repair is authorized.
4. Special Information
(3) Recoverability code.
Recoverability
codes are assigned to support items to indicate the
a. National stock numbers (NSN's) that are
disposition action on unserviceable items.
The
missing from P source coded items have been applied
recoverability code is entered in the fifth position of the
for and will be added to this TM by future
Uniform SMR Code format as follows: Recoverability
change/revision when they are entered in the Army
Master Data File (AMDF).
Until the NSN's are
Codes
Definition
established and published, submit exception requisitions
Z ----- Nonreparable item.
When unserviceable,
to:
Commander, US Army Communications
condemn and dispose at the level indicated in position
Electronics Command and Fort Monmouth, ATTN:
3.
DRSEL-MM, Fort Monmouth, New Jersey 07703 for the
F ----- Reparable item.
When
uneconomically
part required to support your equipment.
reparable, condemn and dispose at the direct support
level.
b. Detailed manufacturing instructions for items
L------ Reparable item.
Repair, condemnation, and
source coded to be manufactured or fabricated are
disposal not authorized below depot/specialized repair
found in TM 11-5820-620-34.
activity level.
c. Detailed assembly instructions for items source
c. National Stock Number. Indicates the National
coded to be assembled are found in TM 11-5820-6234.
stock number assigned to the item and will be used for
Assembly components are listed immediately
requisitioning purposes.
following the item to be assembled.
d. Federal Supply Code for Manufacturer (FSCM).
d. The following publications pertain to the C-
The FSCM is a 5-digit numeric code listed in SB 708-
6709/G and its components:
41/42 which is used to identify the manufacturer,
distributor, or Government agency, etc.
TM 11-5820-615-12, Control, Radio Set C-6709/G.
e. Part Number. Indicates the primary number
TM 11-582061534, Control, Radio Set C-6709/G.
used by the manufacturer (individual, company, firm,
corporation, or Government activity), which controls the
5. How to Locate Repair Parts
design and characteristics of the item by means of its
a. When National stock number or part number is
engineering drawings, specifications, standards, and
unknown.
inspection requirements to identify an item or range of
(1) First.
Using the table of contents,
items.
determine the functional group within which the item
NOTE
belongs.
This is necessary since illustrations are
When a stock numbered item is
prepared for functional groups and listings are divided
requisitioned,
the
repair
part
into the same groups.
received may have a different part
(2) Second. Find the illustration covering the
number than the part being replaced.
functional group to which the item belongs.
f. Description. Indicates the Federal item name
(3) Third. Identify the item on the illustration
and, if required, a minimum description to identify the
and note the illustration figure and item number of the
item. In Special Tools List, the initial basis of issue
item.
(BOI) appears as the last line in the entry for each
(4) Fourth. Using the Repair Parts Listing,
special tool, special TMDE, and other special support
find the figure and item number noted on the illustration.
equipment when density of equipments supported
exceeds density spread indicated in the basis of issue,
b. When National stock number or part number is
the total authorization is increased accordingly.
known.
g. Unit of Measure (U/M). Indicates the standard
(1) First. Using the Index of National Stock
of the basic quantity of the listed item as used in
Numbers and Part Numbers, find the pertinent National
performing the actual maintenance function.
This
stock number or part number. This index is in NIIN
measure is expressed by a two-character alphabetical
sequence followed by a list of part numbers in
abbreviation (e.g., ea, in, pr, etc). When the unit of
alphameric sequence, cross-referenced to the
measure differs from the unit of issue, the lowest unit of
illustration figure number and item number.
issue that will satisfy the required units of measure will
(2) Second. After finding the figure and item
be requisitioned.
number, locate the figure and item number in the repair
h. Quantity Incorporated in Unit. Indicates the
parts list.
quantity of the item used in the breakout shown on the
6. Abbreviations
illustration figure, which is prepared for a functional
group, subfunctional group, or an assembly. A "V"
Not applicable.
appearing in this column in lieu of a quantity indicates
(Next printed page is 4)
2
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |