Special Information - TM-11-5820-554-24P0004

Depot Maintenance Allowance Per 100

and a minimum description required to identify the

Equipment This column indicates opposite the first

item. The last line indicates the reference number

appearance of each item the total quantity authorized for

followed by the applicable Federal Supply Code for

depot maintenance of 100 equipments.

Manufacturer (FSCM) in parentheses. The FSCM is

used as an element in item identification to designate

j. Illustration.

manufacturer or distributor or Government agency, etc.,

(1) Figure number. Not applicable.

and is identified in SB 708-42.

(2) Item number. Indicates the item number or

reference designation used to reference the item.

d. Unit of Measure (U/M). Indicates the standard

or basic quantity by which the listed item is used in

1-4. Special Information

performing the actual maintenance function. This

measure is expressed by a two-character alphabetical

a. Usable on codes are included in column 3.

abbreviation; e.g., ea. in, pr, etc., and is the basis used to

Uncoded items are applicable to all models.

indicate quantities and allowances in subsequent

Identification of the usable on codes used in this

columns. When the unit of measure differs from the

publication are-

unit of issue, the lowest unit of issue that will satisfy the

Code

Used on

required units of measure will be requisitioned.

AQI

AN/FRC-93

e. Quantity Incorporated in Unit. This column

indicates the quantity of the item used in the equipment.

f. The following publication pertains to the AN/

Subsequent appearances of the same item in the same

FRC-93 and its components:

assembly are indicated by the letters "REF".

TM 11-5820-554-15

Organizational, DS, GS, and

Depot Maintenance Manual:

f. 15-Day Organizational Maintenance Allow-

Radio Set AN/FRC-93.

ances.

1-5. Location of Repair Parts

(1) The repair parts indicated by an asterisk in

the allowance column represent those authorized for use

a. This manual contains one cross-reference index

at the organizational category, and will he requisitioned

(see VII) to be used to locate a repair part when either

on an "as required" basis until stockage is based on

the Federal stock number or reference number

demand in accordance with AR 710-2.

(manufacturer' part number) is known. The first

column in the index is prepared in numerical or

(2) Major Army commanders are authorized to

alphanumeric sequence in ascending order.

The

approve reduction in the range of support items

reference numbers (manufacturer' part numbers) are

authorized for use in units within their commands.

listed immediately following the last listed Federal stock

Recommendations for increase in range of items

number in the index of Federal stock numbers.

authorized for use will be forwarded to Commander, US

Army Electronics Command, ATTN:AMSEL-MA-CT,

b. When the Federal stock number or reference

Fort Monmouth, N.J., 07703.

number is known, follow the procedures given in (1) and

(2) below.

(3) Allowance quantities are indicated in the

special tools list section for special tools. TMDE, and

(1) Refer to the index of Federal stock numbers

other support equipment.

(sec VII), and locate the Federal stock number or

g. 30-Day DS/GS Maintenance Allowances

reference number. The FSN and reference number are

cross-referenced to the applicable figure and item

NOTE

number or reference designation.

Allowances in GS column are for GS maintenance

(2) Refer to the repair parts list (see III and V'

only.

and locate the figure number (col 7a-20P, 10a -34P) and

(1) The repair parts indicated by asterisk

item number or reference designation (col 7b-20P. 10b-

entries in separate allowance columns for DS and GS

34P) as noted in the FSN index.

represent those authorized for use at that category of

c. When the figure and item number or reference

maintenance to be requisitioned on an "as required"

designation are known. scrutinize columns 7a and 7b-

basis, until stockage is based on demand in accordance

20P and 10a and 10b-34P of the repair parts list (see III

With AR 710-2.

and V) until the item is located.

(2) Allowance quantities are indicated in the

special tool lists section for special tools, TMDE, and

d. When the FSN, reference number, figure number

other support equipment.

and item number are not know n, scrutinize column 3 of

the repair parts list (see III and V) which is arranged in

1-Year Allowances Per 100 Equipments/

alphabetical order.

Contingency Planning Purposes. Column intentionally

left blank.