Click here to make tpub.com your Home Page

Page Title: Procedure.
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 



(11) If procedure (10) above indicates
(3) Connect the output of AN/URM-
the necessity, tune C317, C312,
25D to test point J301 (fig. 62).
C309, and C306 for maximum volt-
c. Procedure.
age on the ME-26/U (fig. 62).
Warning: Avoid direct contact with the
(12) Repeat procedure (6) through (11)
trimmer shafts of capacitors C306 and
above until no further increase in
C312. The shafts are at B+ potential; do
voltage can be obtained on the ME-
not short them to ground.
26/U.
(13) O p e r a t e t h e M A N U A L F R E -
(1) Set the MANUAL FREQUENCY
QUENCY UNITS control from 9
UNITS control to 9. Set the MAN-
to 0 and tune the AN/URM-25D
UAL FREQUENCY TENTHS con-
f r o m 29.9 to 20.9 mc in cor-
trol to .9.
responding 1.0-mc decrements. At
each control position, check the
Note. In the following procedure, adjust
the AN/URM-25D output level as neces-
tuning of L303, L304, L305, and
sary to maintain the ME-26/U indication
L306 with the tuning wand. Only
between -1 and -2 volts dc.
slight detuning (if any) should be
(2) Turn trimmer capacitors C302,
noted in the middle of the 9 to 0
C304, C306, C309, C312, and C317
range. If considerable detuning is
noted, check the tuning slugs for
(fig. 62) to the right, to their stops.
(3) Adjust slugs of L301 through L306
p r o p e r travel. The slugs should
(fig. 113) so that the tops of the
move linearly for given increments
slugs are 1 inch from the top of the
of rotation, Replace any worn or
cover.
b r o k e n parts or replace L303,
(4) Set the AN/URM-25D frequency
L304, L305, or L306.
to 29.9 mc unmodulated and adjust
(14) Remove the AN/URM-25D and con-
the output level to obtain a read-
nect the TS-497/URR to the ANT.
able indication on the ME-26/U.
jack through the 6-db attenuator
(supplied with the TS-497/URR).
Note. Perform (2) and (3) below only
(15) Set the MANUAL FREQUENCY
when this subunit has been severely mis-
UNITS and the TENTHS controls
aligned.
to 9 and .9, respectively. Set the
(5) I f necessary, check L306, L305,
MANUAL FREQUENCY TENS con-
L304, and L303 with the tuning
trol to 29 or 39. Set the TS-497/
wand (para 132c(7)) for maximum
URR to the same frequency indi-
voltage on ME-26/U.
c a t e d b y t h e  MANUAL FRE-
(6) Set the MANUAL FREQUENCY
QUENCY controls (299.9 or 399.9
UNITS control to 0. Set the MAN-
mc).
UAL FREQUENCY TENTHS con-
Note. In the procedures outlined in
(16)
trol of .0. Set the AN/URM-25D
through (22) below, slightly readjust
the
frequency to 20.0 mc unmodulated.
TS-497/URR for a maximum ME-26/U
in-
(7) Check L306, L305, L304, and L303
dication each time the frequency of
the
TS-497/URR is changed.
with the tuning wand (para 132c(7)).
(8) I f necessary, tune L306, L305,
(16) Adjust the output level of the TS-
497/URR to obtain a readable indi-
L304, and L303 for maximum volt-
cation on the ME-26/U (between -1
age on ME-26/U.
(9) Set the MANUAL FREQUENCY
and -2 volts dc).
(17) Check L302 and L301 (fig. 113) with
UNITS control to 9. Set the MAN-
UAL FREQUENCY TENTHS con-
the tuning wand and adjust, if nec-
trol to .9. Set the AN/URM-25D
essary.
(18) Adjust C302 and C304 (fig. 62) for
frequency to 29.9 mc unmodulated.
(10) Check L306, L305, L304, and L303
maximum indication on the ME-26/
U.
(fig. 113) with the tuning wand.
174


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business