|
| |
- INSTALLATION INSTRUCTIONS FOR SYSTEMS SINGLE CHANNEL GROUND AND AIRBORNE RADIO SYSTEM (SINCGARS) AN/VRC-88F, AN/VRC-89F, AN/VRC-90F, AN/VRC-91F, AN/VRC-92F FORCE XXI BATTLE COMMAND, BRIGADE-AND-BELOW (FBCB2) AN/UYK-128 (V)4
- INSTALLATION INSTRUCTIONS is changed as follows
- LIST OF EFFECTIVE PAGES
- REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
- TABLE OF CONTENTS
- TABLE OF CONTENTS-continued
- CHAPTER 1. INTRODUCTION
- CHAPTER 2. PURPOSE OF INSTALLATION
- CHAPTER 3. COMPLETION TIME FOR INSTALLATION
- CHAPTER 4. PREPARATION FOR INSTALLATION
- Section VIII. EXAMINE EACH ITEM FOR DAMAGE
- Table 4-1. Kit Parts List for Installation of C4ISR Equipment.
- Table 4-1. Kit Parts List for Installation of C4ISR Equipment (Contd).
- Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment.
- Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
- Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
- Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
- CHAPTER 5. INSTALLATION PROCEDURES
- Figure 5-2.
- Figure 5-4.
- Section IV. B-BEAM PREPARATION
- Section V. ASSEMBLY OF CAB ENCLOSURE PANEL
- Section VI. FINAL ASSEMBLY, TERMINAL BOARD WIRING, AND TERMINAL LINK
- Position cab enclosure panel
- Route 24V power cable
- Install cab enclosure panel
- Secure three 24V fuse wire assemblies
- Section VII. INTEGRATED RACK INSTALLATION
- Mount integrated rack
- Section VIII. INSTALLATION OF SINCGARS MOUNTING TRAY AND AMP GUARD
- Section IX. POWER AMPLIFIER INSTALLATION
- Attach control cable
- Section X. FBCB2 COMPONENTS INSTALLATION
- Install ramball mount
- Section X.A. SERIAL INTERFACE ADAPTER DEVICE (SIAD) CABLES INSTALLATION
- Section X.B. SERIAL INTERFACE ADAPTER DEVICE (SIAD) INSTALLATION
- Section X.C. FBCB2 CABLES INSTALLATION
- Install Vehicular Amplifier Adapter (VAA)
- Section XI. LOUDSPEAKER AND MULTI-NET RACK INSTALLATION
- Install lower shelf
- Install assembled multi-net rack
- Install four loudspeakers
- Section XII. FHMUX MOUNT INSTALLATION
- Mount MT-6845/VRC mount
- Section XIII. EPLRS MOUNT INSTALLATION
- Section XIV. SINCGARS ANTENNA INSTALLATION
- Install grommet
- Attach upper antenna element
- Section XV. EPLRS ANTENNA INSTALLATION
- Install grommet
- Section XVI. USER READOUT (URO) BRACKET INSTALLATION
- Section XVII. REAR SINCGARS MOUNT INSTALLATION
- Install SINCGARS mounting base MT-6352/VRC
- Section XVIII. PLGR BRACKET INSTALLATION
- Section XIX. PLGR ANTENNA AND CABLES INSTALLATION (WITHOUT BOLT-ON ARMOR)
- Pull PLGR antenna cable
- Split one side of grommet
- Route PLGR antenna cable
- Figure 5-52.
- Attach shrink tubing
- Section XX. LOUDSPEAKER CABLES INSTALLATION
- Route speaker cables
- Connect two speaker cables
- Figure 5-58.
- Section XXI. ANTENNA CABLE INSTALLATION
- Route antenna cable
- Section XXII. FHMUX ANTENNA CABLES INSTALLATION
- Route white antenna cable
- Route bundle with orange antenna cable
- Coil excess antenna cable
- Section XXIII. FHMUX AND SINCGARS POWER CABLES INSTALLATION
- Route FHMUX power cable
- Connect rear SINCGARS power cable
- Route auxiliary mount power cable
- Route front SINCGARS power cable
- Section XXIV. EPLRS CABLES INSTALLATION
- Route antenna cable
- Figure 5-80.
- Route left side antenna cable
- Bundle antenna cable
- Route INC-EPUU
- Coil excess INC-EPUU cable
- Attach heat shrink tubing
- Section XXV. DVE HOOD CABLE GUIDE INSTALLATION
- Locate, mark, and cut area
- Section XXVI. DVE PAN AND TILT MODULE (PTM) MOUNT ASSEMBLY PREPARATION AND PILLAR MOUNT INSTALLATION
- Section XXVII. DVE A-FRAME CABLE GUIDE AND PAN AND TILT MODULE (PTM) MOUNT ASSEMBLY INSTALLATION
- Using A-frame cable guide
- Install PTM mount assembly
- Section XXVIII. DVE DISPLAY CONTROL MODULE (DCM) ROOF MOUNT INSTALLATION
- Slide bow closeout tube
- Install four rivet nuts
- Install DCM B-pillar roof bracket
- Install loop clamp
- Loosen four hand knobs
- Section XXIX. PAN AND TILT MODULE (PTM) CONTROL MOUNTING BRACKET INSTALLATION
- Section XXX. PAN AND TILT MODULE (PTM) CONTROL ASSEMBLY, CONTROL CABLE ASSEMBLY, AND DCM/PTM INTERCONNECT CABLE INSTALLATION
- Figure 5-101.
- Secure PTM connector end
- Figure 5-104.
- Install control cable seal assembly rubber grommet
- Section XXXI. LCD PROTECTIVE ASSEMBLY INSTALLATION
- Section XXXII. DVE POWER CABLE INSTALLATION
- Figure 5-112
- SECTION XXXIII. WINDSHIELD ARMOR MODIFICATION
- Figure 5-114.
- Figure 5-115.
- Section XXXIV. ARMOR AND ANTENNA INSTALLATION (WITH BOLT-ON ARMOR)
- Figure 5-117.
- Install modified upper capping ring
- Install antenna
- Section XXXV. ANTENNA CABLE INSTALLATION
- Split grommet
- Route antenna cable
- Blank Page
- Blank Page
- Distribution
- RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
- TB-9-2320-280-35-4
- RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
- Blank Page
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
- Blank Page
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
- Blank Page
- RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
- Distribution
- Blank Page
|
Click
here for thousands of PDF manuals