Quantcast MAINTENANCE   PROCEDURE   Continued - TM-11-5821-333-12_120

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: MAINTENANCE PROCEDURE Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
MAINTENANCE   PROCEDURE   Continued - TM-11-5821-333-12_119
Up
TM-11-5821-333-12 Non-ICOM Airborne Radio AN/ARC-201(V) ICOM Airborne Radio AN/ARC-201A(V) Manual
Next
Section  VIl.  PREPARATION  FOR  STORAGE  OR  SHIPMENT


TM   11-5821-333-12 6-33.   MAINTENANCE   PROCEDURE   Continued. 1. HOLD UP BATTERY AND COVER. a.  Fully  loosen  two  captive  screws  and  remove  cover  (6). b.  Replace  battery  (5). c.  Record  battery  installation  or  replacement  date  on  marking  plate  (8). d.  Set  cover  (6)  in  place  and  tighten  two  captive  screws. 2. CONNECTOR CAPS. a.  Loosen  and  remove  screw  (3)  and  washer  (2)  securing  cord  to  fill  device.  Remove  cap  (1  or  7), b.  Aline  eyelet  on  end  of  cord  of  replacement  cap  (1  or  7)  with  hole.  Install  washer  (2)  and  screw  (3). c.   Tighten   screw   (3). 3.  IDENTIFICATION  PLATE. a.  With  pocket  knife,  peel  off  identification  plate  (4). b.  With  cotton  swab  and  alcohol,  clean  adhesive  from  fill  device. c.  Peel  backing  from  new  identification  plate  (4). d.  Press  firmly  into  place. 4. MARKING PLATE. a.  With  pocket  knife,  peel  off  marking  plate  (8). b.  With  cotton  swab  and  alcohol,  clean  adhesive  from  fill  device. c.  Peel  backing  from  new  marking  plate  (8). d.  Press  firmly  into  place. e.  Copy  information  from  old  marking  plate  to  new  marking  plate. 5.   KNOBS. a.  Loosen  set  screws  on  knob  (9). b.  Remove  knob  (9)  and  spacer  (10). c.  Set  spacer  (10)  and  knob  (9)  in  place. d.  Tighten  set  screws  on  knob  (9). 6. BOOT, DUST AND WATER SEAL. a.  Loosen  and  remove  boot  (11)  using  deep  socket.  The  boot  and  nut  are  one  piece. b.  Set  boot  (11)  in  place.  Tighten  using  deep  socket. 7.  GUARDS. a.  Loosen  and  remove  screws  (12)  and  washers  (13)  securing  guards  (14)  to  fill  device. b.  Hold  guard  (14)  in  place.  Install  and  tighten  screws  (12)  and  washers  (13). 6-57


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business