Quantcast REPLACEMENT  OF  ACCESS  COVER.  Continued - TM-11-5820-890-30-5_839

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF ACCESS COVER. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Section  IV.  MAINTENANCE  PROCEDURES (cont) - TM-11-5820-890-30-5_838
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  CONNECTOR  CASE (cont)


TM 11-5820-890-30-5 16-9.  REPLACEMENT  OF  ACCESS  COVER.  Continued . ITEM ACTION REMARKS REMOVAL Continued b.   Two   protective   caps   (2) c.  Four  spanner  nuts  (3) d.   Four   electrical   connector retainers  (4) e.   Access   cover INSTALLATION f. g. h. i. j. k. l. Access   cover Four  o-rings J1  through  J4 (1) (1) connectors (7)  through  (10) Four   electrical   connector retainers  (4) Four spanner nuts  (3) Eight  screws  (5) and  Iockwashers  (6) Two  protective  caps  (2) Remove  and  inspect  two  protective  caps (2)  from  J4  and  J2  connectors  (9)  and (10).   If   damaged,   obtain   replacement. Use  spanner  wrench  with  1-1/4-inch  spanner wrench  attachment.  Remove  and  inspect four  spanner  nuts  (3)  from  J1  through  J4 connectors   (7)   through   (10).   If   damaged, obtain   replacement. Remove  and  inspect  four  electrical  connector retainers  from  four  connectors.  If  damaged, obtain   replacement. Remove  and  discard  defective  access  cover  (1). Obtain  replacement  access  cover  (1). Coat  o-rings  of  four  connectors  (7) through  (10)  with  silicone  compound. Install  four  connectors  in  four  connector holes  in  access  cover  (1). Install  four  electrical  connector  retainers (4)  on  four  connectors. Use  spanner  wrench.  Install  and  hand tighten  four  spanner  nuts  (3)  securing four  connectors  to  access  cover  (1). Use  torque  wrench  and  1-1/4-inch spanner  wrench  attachment.  Torque nuts  to  100  in-lb. Use  cross  tip  screwdriver.  Install  and hand  tighten  eight  screws  (5)  and Iockwashers  (6)  securing  access cover  (1)  to  connector  case  (12). Use  torque  screwdriver.  Torque screws  to  8  to  10  in-lb. Install  two  protective  caps  (2)  on  J4 and  J2  connectors  (9)  and  (10). If  a  screw  is  not  stripped but  will  not  tighten,  refer to  paragraph  16-16  for replacement  of  its  threaded screw  insert  (if  present). If  a  tapped  hole  is  defec- tive,  refer  to  paragraph 16-10  for  replacement  of the   connector   case.   (12). 16-6


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business