Quantcast REPLACEMENT OF BATTERY TRAY CASE.  Continued - TM-11-5820-890-30-5_827

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF BATTERY TRAY CASE. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF BATTERY TRAY CASE.  Continued - TM-11-5820-890-30-5_826
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF BATTERY TRAY CASE.  Continued - TM-11-5820-890-30-5_828


TM 11-5820-890-30-5 15-33. REPLACEMENT OF BATTERY TRAY CASE.  Continued ITEM ACTION REMARKS INSTALLATION  Continued u.   O-ring .                    J1  connector  (5) w.  U1  voltage  regulator  (10) x.   O-ring y.                     AZ   connector board  CCA  (13)  and P1  connector  (17) z.                      DS1  lamp holder  (14) aa. Light lens ab.                S1  pushbutton switch  (16) ac.  R1  resistor  (1) ad.  VR1  zener  diode  (3) ae.  Four  catch  strikes  (8) Apply  small  amount  of  silicone  compound to  o-ring  on  retained  J1  connector  and, while  wet,  install  connector  in  chassis. Install  to  chassis. Install  to  chassis. Apply  small  amount  of  silicone  compound to  o-ring  on  retained  P1  connector  and, while  wet,  install  connector  in  chassis. Install  to  chassis. Install  to  chassis. Install. Install  to  chassis. Install  to  chassis. Install  to  chassis. Use  cross  tip  screwdriver.  Install  eight retained  screws,  flat  washers,  and  lock- washers  (6)  securing  four  catch  strikes (8)  to  chassis.  See  figure  15-4. Refer  to  paragraph  15-26 for  installation  of  J1 connector. Refer  to  paragraph  15-27 for  installation  of  U1 voltage   regulator. Refer  to  paragraph  15-23 for  installation  of  A2  con- nector  board  CCA  and  P1 connector.  Ensure  that 27  pins  of  P1  connector (17)  are  securely  connect- ed  to  AZ  connector  board CCA  (13). Refer  to  paragraph  15-30 for  installation  of  DS1  lamp holder. Refer  to  paragraph  15-32 for  installation  of  S1 pushbutton  switch. Refer  to  paragraph  15-24 for installation of R1 resistor. Refer  to  paragraph  15-25 for  installation  of  VR1  zener diode. Inspect  each  screw  and  its threaded  screw  insert to  determine  if  any is  defective.  If  a  screw  is not  stripped  but  will  not tighten,  refer  to  paragraph 15-35  for  removal  and replacement   of   threaded screw  inserts. 15-38


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business