Quantcast REPLACEMENT OF BATTERY TRAY CASE.  Continued - TM-11-5820-890-30-5_826

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF BATTERY TRAY CASE. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF BATTERY TRAY CASE (cont)
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF BATTERY TRAY CASE.  Continued - TM-11-5820-890-30-5_827


TM 11-5820-890-30-5 15-33. REPLACEMENT OF BATTERY TRAY CASE.  Continued ITEM ACTION REMARKS REMOVAL Continued h.   S1   pushbutton   switch   (16) Remove  and  retain. i. R1  resistor  (1) Remove  and  retain. j. VR1  zener  diode  (3) Remove  and  retain. k.   A1   battery   tray   CCA   (8) l. E1  terminal  lug  (12) m.  Battery  tray  gasket  (3) n.   Battery   tray subassembly   (1) o.   Four   catch   strikes   (8) p.   Seal   screw   (7) q.   Battery   tray   case   (18) INSTALLATION r.   Battery   tray   case   (18) s.   Battery   tray subassembly   (1) t.   A1   battery   tray   CCA   (8) Remove  and  retain. Remove  and  retain. Remove  and  inspect  for  cuts  and  tears. If   defective,   obtain   replacement. See  figure  15-4. Remove  and  retain  all  components, circuit   card   assemblies,   and   connectors that  were  disconnected  from  chassis. Use  cross  tip  screwdriver.  Remove  and inspect  eight  screws,  flat  washers,  and Iockwashers  (6)  securing  four  catch strikes  (8)  to  chassis.  Remove  and inspect  four  catch  strikes.  If  damaged, obtain   replacement. Use  flat  tip  screwdriver.  Remove  and inspect  seal  screw.  If  damaged,  obtain replacement. Remove  and  discard.  See  figure  15-5. Obtain  replacement  battery  tray  case. Place  all  retained  components,  circuit card   assemblies,   and   connectors   into replacement  battery  tray  case  (18) chassis. Install  to  chassis. Refer  to  paragraph  15-32 for  removal  of  S1 pushbutton   switch. Refer  to  paragraph  15-24 for  removal  of  R1  resistor. Refer  to  paragraph  15-25 for  removal  of  VR1  zener diode. Refer  to  paragraph  15-22 for  removal  of  A1  battery tray  CCA. Refer  to  paragraph  15-28 for  removal  of  E1  terminal lug. Refer  to  paragraph  15-21 for   removal   of   battery tray  gasket. Inspect  each  screw  and  its threaded  screw  insert  to determine  if  any  are  defec- tive.  If  a  screw  is  not stripped  but  will  not  tighten, refer  to  paragraph  15-35  for removal  and  replacement  of threaded   screw   inserts. Refer  to  paragraph  15-31 for  removal  of  seal  screw. These  were  removed  in step  n. Refer  to  paragraph  15-22 for  installation  of  A1  battery tray  CCA. 15-37


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business