Quantcast REPLACEMENT OF POWER SUPPLY ADAPTER CHASSIS ASSEMBLY. Continued - TM-11-5820-890-30-5_783

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF POWER SUPPLY ADAPTER CHASSIS ASSEMBLY. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF POWER SUPPLY ADAPTER CHASSIS ASSEMBLY. Continued - TM-11-5820-890-30-5_782
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF POWER SUPPLY ADAPTER CHASSIS ASSEMBLY. Continued - TM-11-5820-890-30-5_784


TM 11-5820-890-30-5 14-40. REPLACEMENT OF POWER SUPPLY ADAPTER CHASSIS ASSEMBLY.  Continued ITEM ACTION REMARKS INSTALLATION  Continued bk. bl. Power  supply  adapter chassis  assembly  (1) Screw  and  flat  washer (4)  and  two  terminal lugs  (5) bm. bn. Four  screws,  flat washers,  and Iockwashers  (12) Diode  CCA  (11)  wires bo.  Four  screws,  flat washers,  and Iockwashers  (10) bp.  Terminal  board  (8) wires  and  six screws  (9) bq.  Two  screws,  flat washers,  and Iockwashers  (7) br.   Relay   (6)   wires bs.   Four   screws,   flat washers,  and Iockwashers  (3) bt.   Two-wire   transient protection  CCA  (2) wires 14-72 Set  upside  down  on  work  surface  with front  toward  you.  Route  the  wiring harness  as  shown  in  figure  14-10. Use  cross  tip  screwdriver.  Install  and tighten  retained  screw,  flat  washer, and  two  terminal  lugs  securing  the wiring  harness  to  E3  on  the  chassis. Use  cross  tip  screwdriver.  Install  and tighten  four  retained  screws,  flat  washers, and  replacement  Iockwashers  securing  the retained  A2  diode  CCA  on  the  chassis. Use  soldering  kit,  soldering  aid,  and  heat sink.  Solder  tagged  wires  to  correct terminal  posts  on  the  A2  diode  CCA, and  remove  wire  tags. Use  cross  tip  screwdriver.  Install  and tighten  four  retained  screws,  flat  washers, and  replacement  Iockwashers  securing the  retained  TB1  terminal  board  (8)  on the  chassis. Use  flat  tip  screwdriver.  Install  and  tighten six  retained  screws  securing  tagged  wires to  terminals  on  the  terminal  board. Remove  wire  tags. Use  cross  tip  screwdriver.  Install  and tighten  two  retained  screws,  flat  washers, and  replacement  Iockwashers  securing the  retained  K1  relay  (6)  on  the  chassis. Use  soldering  kit,  soldering  aid,  heat sink,  and  needle  nose  pliers.  Install  and solder  tagged  wires  on  correct  terminals of  the  relay,  and  remove  wire  tags. Use  cross  tip  screwdriver.  Install  and tighten  four  retained  screws,  flat  washers, and  replacement  Iockwashers  securing the  retained  two-wire  transient  CCA  on the  chassis. Use  soldering  kit,  soldering  aid,  and  heat sink.  Solder  tagged  wires  to  correct terminal  posts  on  the  two-wire  transient CCA,  and  remove  wire  tags. Before  and  after  soldering, clean  wires  and  terminal posts  with  alcohol  and cotton  swabs. Position terminal board TB1 with  terminals  for  wires closest  to  connector  P1. Position K1 relay with pins for  wires  closest  to  CB1 circuit   breaker. Before  and  after  soldering, clean  wires  and  terminals with  alcohol  and  cotton swabs. Before  and  after  soldering, clean  wires  and  terminal posts  with  alcohol  and cotton  swabs.


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.