Quantcast REPLACEMENT OF E1 OR E2 BINDING POST.  Continued

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF E1 OR E2 BINDING POST. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF LAMP HOLDER FOR DS1 LAMP.  Continued
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  J1  CONNECTOR.  Continued


TM 11-5820-890-30-5 14-37. REPLACEMENT OF E1 OR E2 BINDING POST.  Continued ITEM ACTION REMARKS REMOVAL  Continued c. Binding  post  (14)  or  (15) wires d. Hex  nut,  Iockwasher, flat  washer,  and nylon washer e. Binding  post  (14)  or  (15) INSTALLATION f. g. h. i. j. Binding  post  (14)  or  (15) O-ring Hex  nut,  flat washer,   Iockwasher, and  nylon  washer Binding  post  (14)  or  (15) wires Heat   sink assembly 14-38. REPLACEMENT Tools: OF J1 Flat  tip  screwdriver Torque   screwdriver Flat  tip  bit Socket  wrench 1  1/16  inch  socket Expendable  Supplies: Solder Silicone   compound 14-58 Use  soldering  kit,  soldering  aid,  and heat  sink.  Tag  location  of  all  wires soldered  to  terminals  on  rear  of  binding post.  Unsolder  each  wire  from  the binding  post. Use  5/16  inch  wrench.  Remove  and discard  hex  nut,  Iockwasher,  flat  washer, and  nylon  washer  securing  binding  post to  chassis. Remove  and  discard  defective binding  post. Obtain  replacement  binding  post,  hex  nut, Iockwasher,  flat  washer,  and  nylon  washer. Apply  silicone  compound  to  o-ring  on replacement   binding   post. Use  5/16  inch  wrench.  Install  and  hand tighten  replacement  hex  nut,  Iockwasher, flat  washer,  and  nylon  washer  securing binding  post  to  chassis.  Use  torque wrench.  Torque  to  6  in-lb. Use  soldering  kit,  soldering  aid,  and  heat Before  and  after  soldering, sink.  Solder  tagged  wires  to  terminals clean  wires  and  binding on  rear  of  the  binding  post,  and  remove post  terminals  with  alcohol wire  tags. and  cotton  swabs. Install  retained  heat  sink  assembly  on Refer  to  paragraph  14-17 power  supply  adapter  chassis  (1). for  heat  sink  installation. CONDUCTOR. Soldering  kit Soldering  aid Heat sink Torque  wrench Alcohol Cotton  swabs


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business