Quantcast REPLACEMENT OF  BINDING  POSTS

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF BINDING POSTS
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  ACCESS  COVER.  Continued - TM-11-5820-890-30-5_654
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  BINDING  POSTS.  Continued


TM 11-5820-890-30-5 8-17.  REPLACEMENT Tools: OF  BINDING  POSTS. Flat  tip  screwdriver 5/16-inch  open  end  wrench 5/16-inch   socket Soldering  kit Soldering  aid Heat sink Torque  wrench Torque   screwdriver Expendable  Supplies: Solder Alcohol Cotton  swabs ITEM ACTION REMARKS REMOVAL a.   Access   cover   (27) b.   Wires c.   Bus   wires d.   Two-wire   transient   protec- tion  CCA  (26) e.   Binding   post   (28) Use  flat  tip  screwdriver.  Fully  loosen  five captive  screws  (31).  Remove  cover  to allow   resoldering. Use  soldering  kit.  Tag  and  desolder  three wires  from  terminals  of  two-wire  transient protection  CCA  (26). Use  soldering  kit.  Desolder  bus  wires  from defective  binding  post  (28). Use  cross  tip  screwdriver.  Remove  and retain  four  screws  (9),  Iockwashers  (8), and  flat  washers  (7)  securing  CCA  to access   cover. Use  5/16-inch  open  end  wrench.  Remove and  retain  nut,  Iockwasher,  and  flat  wash- er  securing  defective  binding  post  to  ac- cess  cover.  Remove  and  discard  defect- ive  binding  post. INSTALLATION f.   Binding   post   (28) g.                         Binding post  (28) h.   Two-wire   transient protection  CCA  (26) i. Bus wires j. Wires Obtain   replacement. Position  replacement  binding  post  to  ac- cess  cover.  Use  torque  wrench  and  5/16- inch  socket.  Install  retained  nut,  lockwash- er,  and  flat  washer  securing  binding  post to  access  cover.  Torque  nut  to  5  to  7  in-lb. Position  retained  CCA  to  access  cover. Use  cross  tip  screwdriver.  Install  four  re- tained  screws  (9),  Iockwashers  (8),  and flat  washers  (7)  securing  CCA  to  access cover. Use  soldering  kit.  Position  and  solder  bus wires  to  binding  post  (28). Use  soldering  kit.  Position  and  solder  three tagged  wires  to  terminals  E1  thru  E3  of  two- wire  transient  protection  CCA. This  was  removed  in step  e. These  was  removed  in step  d. NOTE Before  and  after  soldering, clean  wires  and  solder joints  with  alcohol  and cotton  swabs. 8-14


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business