Quantcast REPLACEMENT OF FL2 FILTER. Continued - TM-11-5820-890-30-5_634

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF FL2 FILTER. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF FL1 FILTER. Continued
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF FL2 FILTER. Continued - TM-11-5820-890-30-5_635


TM 11-5820-890-30-5 7-14. REPLACEMENT OF FL2 FILTER. Continued ITEM ACTION REMARKS REMOVAL a.   Eight   screws   (5)   and Iockwashers  (6) b.   FL1   filter   (20)   and FL2  filter  (21)  top terminal c.   Three   screws   (25), Iockwashers  (24),  and flat  washers  (23) d.   Filter   mounting   plate   (22) e.   FL2   filter   (21)   bottom terminal f.   Hex   nut   (29)   and Iockwasher  (28) g.   FL2   filter   (21) INSTALLATION h.   FL2   filter   (21) i. Filter  mounting  plate  (22) l. Hex  nut  (29)  and Iockwasher  (28) k.   FL1   filter   (20)   and FL2  filter  (21)  terminals l. FL1  filter  (20)  and FL2  filter  (21)  wires Use  cross  tip  screwdriver.  Remove  and inspect  eight  screws  (5)  and  lockwash- ers  (6)  securing  access  cover  (1)  to connector   case   (12).   If   damaged, obtain   replacement.   Lay   access   cover to  one  side.  See  figure  7-2. Use  soldering  kit.  Desolder  wire  from top  terminal  of  FL1  filter  (20)  and FL2  filter  (21). Use  cross  tip  screwdriver.  Remove and  inspect  three  screws  (25), Iockwashers  (24),  and  flat  washers (23)  securing  filter  mounting  plate (22)  to  connector  case  (12).  If damaged,   obtain   replacement. Lift  filter  mounting  plate  (22)  to allow  access  to  bottom  terminal  of FL2  filter  (21). Use  soldering  kit.  Desolder  wire  from bottom  terminal  of  FL2  filter  (21). Use  3/8-inch  wrench.  Remove  and inspect  hex  nut  (29)  and  Iockwasher (28)  securing  FL2  filter  (21)  to  filter mounting  plate  (22).  If  damaged, obtain   replacement. Remove  and  discard  defective  FL2 filter   (21). Obtain  replacement  FL2  filter  (21). Install  FL2  filter  (21)  in  mounting hole  of  filter  mounting  plate  (22). Use  3/8-inch  wrench.  Install  and hand  tighten  hex  nut  (29)  and  lock- washer  (28)  securing  FL2  filter  (21) to  filter  mounting  plate  (22). Using  cotton  swabs  and  alcohol, clean  both  terminals  on  FL2  filter  (21) and  top  terminal  on  FL1  filter  (20). Use  soldering  kit.  Solder  wires  to  correct terminals  of  FL2  filter  (21)  and  top terminal  on  FL1  filter  (20). Inspect  each  screw  and  its threaded  screw  insert  (if present)  to  determine  if any  is  defective.  If  a  screw is  stripped,  do  not  replace its  threaded  screw  insert. If  the  holes  are  tapped, there  will  be  no  threaded screw  insert. 7-15


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business