Quantcast REPLACEMENT  OF  FL1  FILTER (cont) - TM-11-5820-890-30-5_632

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF FL1 FILTER (cont)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF J5 CONNECTOR.  Continued
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF FL1 FILTER. Continued


TM 11-5820-890-30-5 7-13.  REPLACEMENT  OF  FL1  FILTER. Tools: Cross  tip  screwdriver 5/16-inch   wrench Expendable  supplies: Solder Alcohol Soldering  kit Cotton  swabs References: Paragraph  7-10  for  removal  and  installation  of  connector  case. Paragraph  7-16  for  removal  and  installation  of  threaded  screw  inserts. ITEM ACTION REMARKS REMOVAL a.   Eight   screws   (5)   and Iockwashers  (6) b.   FL1   filter   (20)   top terminal c.   Three   screws   (25), Iockwashers  (24),  and flat  washers  (23) d.   Filter   mounting   plate   (22) e.   FL1   filter   (20)   bottom terminal f.   Hex   nut   (27)   and Iockwasher  (26) g.   FL1   filter   (20) INSTALLATION h.   FL1   filter   (20) Use  cross  tip  screwdriver.  Remove  and inspect  eight  screws  (5)  and  lockwash- ers  (6)  securing  access  cover  (1)  to connector  case  (12).  If  damaged, obtain   replacement.   Lay   access   cover to  one  side.  See  figure  7-2. Use  soldering  kit.  Desolder  wire  from top  terminal  of  FL1  filter  (20). Use  cross  tip  screwdriver.  Remove and  inspect  three  screws  (25), Iockwashers  (24),  and  flat  washers (23)  securing  filter  mounting  plate (22)  to  connector  case  (12).  If damaged,   obtain   replacement. Lift  filter  mounting  plate  (22)  to allow  access  to  bottom  terminal  of FL1  filter  (20). Use  soldering  kit.  Desolder  wire  from bottom  terminal  of  FL1  filter  (20). Use  5/16-inch  wrench.  Remove  and inspect  hex  nut  (27)  and  Iockwasher (26)  securing  FL1  filter  (20)  to  filter mounting  plate  (22).  If  damaged, obtain   replacement. Remove  and  discard  defective  FL1 filter   (20). Obtain  replacement  FL1  filter  (20). Inspect  each  screw  and  its threaded  screw  insert  (if present)  to  determine  if any  is  defective.  If  a  screw is  stripped,  do  not  replace its  threaded  screw  insert. If  the  holes  are  tapped, there  will  be  no  threaded screw  insert. 7-13


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc.