Quantcast REPLACEMENT  OF CONNECTOR CASE.  Continued - TM-11-5820-890-30-5_627

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF CONNECTOR CASE. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  CONNECTOR  CASE
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF CONNECTOR CASE.  Continued - TM-11-5820-890-30-5_628


TM 11-5820-890-30-5 7-10.  REPLACEMENT  OF CONNECTOR CASE.  Continued ITEM ACTION REMARKS REMOVAL Continued g. h. i. j. k. Screw  (19)  and Iockwasher  (18) Three  (or  two)  screws (25),  flat  washers  (24), and  Iockwashers  (23) Filter  mounting  plate  (22) or  FILTER  EMI-CCA, and  wiring  harness Seal screw (11 ) Connector  case INSTALLATION l. m. n. o. Connector  case Seal  screw  (11) (12) (12) Filter  mounting  plate  (22) or  FILTER  EMI-CCA, and  wiring  harness Three  (or  two)  screws (25),  flat  washers  (24), and  Iockwashers  (23) Use  cross  tip  screwdriver.  Remove  and inspect  screw  (19)  and  Iockwasher  (18) securing  E1  terminal  lug  (17)  next  to filter  mounting  plate  (22).  If  damaged, obtain   replacement.   See   note. Use  cross  tip  screwdriver.  Remove  and inspect  three  (or  two)  screws  (25),  flat washers  (24),  and  Iockwashers  (23) securing  filter  mounting  plate  (22)  or FILTER  EMI-CCA  to  connector  case  (12). If   damaged,   obtain   replacement. Remove  filter  mounting  plate  (22)  or FILTER EMI-CCA, and wiring harness from connector   case   (12).   If   damaged, obtain   replacement. Use  flat  tip  screwdriver.  Remove  seal screw  (11)  from  connector  case  (12), and  inspect  it.  If  damaged,  obtain replacement. Discard  defective  connector  case  (12). Obtain   replacement   connector   case   (12). Use  flat  tip  screwdriver.  Install  and  hand tighten  seal  screw  (11)  in  connector case   (12). Place  filter  mounting  plate  (22) or FILTER EMI-CCA, and wiring harness  in  connector  case  (12). Use  cross  tip  screwdriver.  Install  and hand  tighten  three  or  two  screws  (25), flat  washers  (24),  and  Iockwashers  (23). NOTE For versions with a FILTER EMI-CCA  this  terminal  lug is  screwed  to  the  CCA  and connector   case. NOTE For  versions  with  a FILTER  EMI-CCA  there will  be  hardware  for  only two  holes  after  removal of  ground  lug  in  step  g. NOTE For  versions  with  a FILTER EMI-CCA two sets  of  hardware  are installed  on  the  side  of the  CCA  that  contains two  holes. 7-8


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business