Quantcast REPLACEMENT  OF SNAP LINE DRIVER CCA.  Continued

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF SNAP LINE DRIVER CCA. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  TERMINAL  BLOCK  TB1.  Continued - TM-11-5820-890-30-5_514
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF REMOTE CONTROL TRANSFORMER CCA (cont) - TM-11-5820-890-30-5_516


TM 11-5820-890-30-5 4-72.  REPLACEMENT  OF SNAP LINE DRIVER CCA.  Continued ITEM ACTION REMARKS REMOVAL Continued f.   SNAP   line   driver Using  cross  tip  screwdriver,  remove  and See  figure  4-22. CCA (25) retain  two  screws  (26),  Iockwashers,  flat washers,  and  non-metallic  washers  securing SNAP  line  driver  CCA  (25)  to  power  supply cover   (3). Remove  tiedown  straps  as  required.  Using soldering  kit,  tag  and  desolder  wires  from terminals  E1  through  E18  on  defective  SNAP line  driver  CCA  (25).  Remove  and  discard defective  SNAP  line  driver  CCA. g,   Wires INSTALLATION h.   Wires i. SNAP line driver CCA (25) j. Heatsink  assembly  (11) k.  Screw  (9)  and flat  washer l. Screw  (10) 20 captive m. screws  (8) Solder  tagged  wires  to  terminals  El Before  and  after  soldering, through  E18  on  replacement  SNAP  line clean  wires  and  terminals driver  CCA  (25).  Remove  wire  tags. with  alcohol  and  cotton swabs. Using  cross  tip  screwdriver,  install  two These  were  removed  in retained  screws  (26),  Iockwashers,  flat step  f. washers,  and  non-metallic  washers securing  replacement  SNAP  line  driver CCA  (25)  to  power  supply  cover  (3). Align  heatsink  assembly  (11)  to  power supply  cover  (17). Using  cross  tip  screwdriver,  install  retained  These  were  removed  in screw  (9)  and  flat  washer  securing  heatsink  step  c. assembly  to  audio  amplifier  chassis  (3). Using  flat  tip  screwdriver,  install  and  retain-  These  were  removed  in ed  screw  (10)  securing  heatsink  assembly step  d. (11)  to  audio  amplifier  chassis  (3). Using  torque  screwdriver,  tighten  20 These  were  removed  in captive  screws  (8)  securing  heatsink step  b. assembly  (11)  to  power  supply  cover (17).  Torque  screws  to  8  to  10  in-lb. 4-192


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business