Quantcast REPLACEMENT  OF  POWER  CONTROL  CHASSIS  O-RING  GASKET (cont)

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF POWER CONTROL CHASSIS O-RING GASKET (cont)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF TERMINAL BLOCK TB2
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT TM 11-5820-890-30-5 OF  POWER  CONTROL  CHASSIS  O-RING  GASKET.  Continued - TM-11-5820-890-30-5_510


TM 11-5820-890-30-5 4-70.  REPLACEMENT  OF  POWER  CONTROL  CHASSIS  O-RING  GASKET. Tools: Cross  tip  screwdriver Flat  tip  screwdriver Expendable  Supplies: Sealing  compound,  grade  H Adhesive,   cyanoacrylate Silicone   compound References: Paragraph  3-24  and  3-25  for  repair  instructions  and  removal  and  installation  of threaded  screw  inserts. Paragraph  4-62  for  removal  and  installation  of  circuit  breaker  CB1. ITEM ACTION REMARKS REMOVAL a.  Mounting  adapter b.   Side   access   cover c.   Terminal   block TB2 (19) d.  Screw  (18) Set  on  work  surface  with  left  side  toward you. (16) Remove  and  retain. Tag  wires  on  terminal  block  TB2  (19). Using  flat  tip  screwdriver,  remove  and retain  four  screws  securing  wires  to terminal  block  TB2  (19). Tag  terminal  lugs.  Using  cross  tip  screw- driver,  remove  and  retain  screw  (18),  flat e.  Relay  K1  (15) f.   Four   hex   screws   (11) and  flat  washers  (12) g.   Four   screws   (2) h.  Two  screws  (1)  and flat  washers  (2) i. O-ring  gasket  (4) washer,  Iockwasher,  and  insulating  washer securing  two  terminal  lugs  to  terminal block  TB2  (19). Tag  terminal  lugs.  Using  cross  tip  screw- driver,  remove  and  retain  screw  (16) securing  two  terminal  lugs  to  relay  K1. Using  hex  wrench,  remove  and  retain  four screws  (11)  and  flat  washers  (12)  securing power  control  chassis  to  power  supply chassis. Using  cross  tip  screwdriver,  remove  and retain  four  screws  (2)  securing  side  panel (6)  to  power  control  chassis. Using  cross  tip  screwdriver,  remove  and retain  two  screws  (1)  and  flat  washers  (2) securing  bottom  shelf  to  power  control chassis.  Remove  and  retain  power  control chassis. Inspect,  remove,  and  replace  as  required. Clean  case  channel  of  all  debris. Refer  to  paragraph  4-62 for   removal   procedures. See  figure  4-19. See  figure  4-20. See  figure  4-19. See  figure  4-20. See  figure  4-21. 4-186


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business