Quantcast REPLACEMENT OF TERMINAL BLOCK TB2

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF TERMINAL BLOCK TB2
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF  DIODE  CR6
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  POWER  CONTROL  CHASSIS  O-RING  GASKET (cont)


TM 11-5820-890-30-5 4-69. REPLACEMENT OF TERMINAL BLOCK TB2. Tools: Cross  tip  screwdriver Flat  tip  screwdriver Torque   screwdriver Soldering  kit Expendable  Supplies: Cotton  swabs Alcohol Solder References: Paragraph  4-62  for  removal  and  installation  of  circuit  breaker  CB1. ITEM ACTION REMARKS REMOVAL a.  Mounting  adapter Set  on  work  surface  with  left  side  toward you . b.   Side   access   cover   (16) Remove  and  retain. Refer  to  paragraph  4-62 for   removal   procedures. c.  Terminal  block  TB2  (19) Using  cross  tip  screwdriver,  remove  and retain  two  screws  (18),  Iockwashers,  flat washers,  and  insulating  washers  securing defective  terminal  block  TB2  (19)  to  power control  chassis  (8).  Remove  terminal  block TB2  to  allow  for  resoldering. d.   Wires INSTALLATION e.   Wires Tag  wires  of  terminal  block  TB2.  Using flat  tip  screwdriver,  remove  and  retain four  screws  securing  terminal  lugs  with tagged  wires  to  terminal  block  TB2  (19). Using  soldering  kit,  tag  and  desolder  wires from  defective  terminal  block  TB2  (19). Discard  defective  terminal  block  TB2. Using  soldering  kit,  solder  tagged  wires to  correct  terminals  of  terminal  block  TB2 (19).  Using  flat  tip  screwdriver,  install four  retained  screws  securing  terminal lugs  with  tagged  wires  to  terminal  block TB2  (19).  Remove  wire  tags. f.   Terminal   block   TB2   (19) Using  cross  tip  screwdriver,  install  two retained  screws  (18),  Iockwashers,  flat washers,  and  insulating  washers  securing replacement  terminal  block  TB2  (19)  to power  control  chassis  (8). g.                Side  access Install. cover  (16) See  figure  4-20. See  figure  4-19. See  figure  4-20.  These were  removed  in  step  d. Before  and  after  soldering, clean  wires  and  terminals with  alcohol  and  cotton swabs. These  were  removed  in step  c. See figure 4-14. This was removed  in  step  b. Refer  to  paragraph  4-62  for installation   procedures. 4-185


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business