Quantcast REPLACEMENT OF DIODE CR6. Continued

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF DIODE CR6. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  SIDE  PANEL.  Continued - TM-11-5820-890-30-5_458
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  TERMINAL  BLOCK  TB2.  Continued


TM 11-5820-890-30-5 4-37. REPLACEMENT OF DIODE CR6. Continued ITEM ACTION REMARKS INSTALLATION e.  Diode  CR6  (28) f. Relay K1 (31) Rear  access g. cover  (12) 4-38.  REPLACEMENT Tools: Noting  polarity,  solder  replacement  diode CR6  (28)  to  leads  X1  and  X2  of  retained relay  K1  (31). Position  retained  relay  K1  (31)  on  two electrical  posts  (27)  on  power  control chassis  (17).  Using  cross  tip  screwdriver, install  two  retained  screws  (29),  lock- washers  (23),  and  terminal  lugs  (30) securing  relay  K1  (31)  to  power  control chassis   (17). Hold  in  place  and  tighten  six  captive screws  (13)  securing  rear  access  cover (12)  to  power  control  chassis  (10). Using  torque  screwdriver,  torque screws  to  8  to  10  in-lb. OF  TERMINAL  BLOCK  TB2. Cross  tip  screwdriver Flat  tip  screwdriver Before  and  after  soldering, clean  solder  joints  with alcohol  and  cotton  swabs. Apply  one  drop  of  grade  H sealing  compound  to threads  of  two  retained screws  before  installation. This  was  removed  in step  b. See  figure  4-5. Torque   screwdriver ITEM ACTION REMARKS REMOVAL a.  Mounting  adapter b.  Six  captive  screws  (13) and  rear  access  cover (12) c.   Wires d.  Terminal  block  TB2  (32) Set  on  work  surface  with  left  side  toward you. Using  flat  tip  screwdriver,  fully  loosen  six See  figure  4-5. captive  screws  (13)  securing  rear  access cover  (12)  to  power  control  chassis  (10). Remove  and  retain  rear  access  cover. Tag  wires  of  terminal  block  TB2  (32). See  figure  4-10. Using  flat  tip  screwdriver,  remove  and retain  four  screws  securing  shorting  bar (39)  and  terminal  lugs  (33)  with  tagged wires  to  terminal  block  TB2  (32). Using  cross  tip  screwdriver,  remove  and retain  four  screws  (35),  Iockwashers  (23), and  flat  washers  (24)  securing  defective terminal  block  TB2  (32)  to  power  control chassis  (17).  Remove  and  discard defective  terminal  block  TB2. 4-136


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business