Quantcast REPLACEMENT  OF  SIDE  PANEL.  Continued - TM-11-5820-890-30-5_457

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF SIDE PANEL. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  SIDE  PANEL.  Continued - TM-11-5820-890-30-5_456
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  SIDE  PANEL.  Continued - TM-11-5820-890-30-5_458


TM 11-5820-890-30-5 4-36.  REPLACEMENT  OF  SIDE  PANEL.  Continued ITEM ACTION REMARKS l. Shoulder  pin  (4) m.  Side  panel  (8) INSTALLATION n.   Shoulder   pin   (4) REMOVAL Continued k.   J1   protective   cap   (3) Using  cross  tip  screwdriver,  remove  and retain  screw  (1)  and  flat  washer  (2) securing  J1  protective  cap  (3)  to  defective side  panel  (8).  Remove  and  retain  J1 protective   cap. Using  adjustable  wrench  and  1/2-inch open-end  wrench,  remove  and  retain  hex nut  (7),  Iockwasher  (6),  and  flat  washer (5)  securing  shoulder  pin  (4)  to  side  panel (8).  Remove  and  retain  shoulder  pin. Discard  defective  side  panel. o.   J1   protective   cap   (3) p.   Side   panel   (8) Obtain  replacement  side  panel  (8). Position  retained  shoulder  pin  (4),  hex  nut (11),  Iockwasher  (10),  and  flat  washer (9)  to  side  panel  (12).  Using  adjustable wrench  and  1/2-inch  open-end  wrench, tighten   nut. Using  cross  tip  screwdriver,  install  retained screw  (1)  and  flat  washer  (2)  securing retained  J1  protective  cap  (3)  to  side panel   (8). Position  replacement  side  panel  (8)  to power  control  chassis  (17).  Using  cross tip  screwdriver,  install  four  retained  screws (36)  securing  replacement  side  panel  to power  control  chassis  (17). q.   Mounting   rail   (9) Using  cross  tip  screwdriver,  install  seven retained  screws  (37)  securing  retained mounting  rail  (9)  to  side  panel  (8). r. Five  screws  (7  and  8) Using  cross  tip  screwdriver,  install  five retained  screws  (7  and  8)  securing  top shelf  (9)  to  mounting  rail  (10)  on  side panel  (6)  of  power  control  chassis  (4). s.  Two  screws  (1)  and  flat Using  cross  tip  screwdriver,  install  two washers  (2) retained  screws  (1)  and  flat  washers  (2) securing  bottom  shelf  (3)  to  power control   chassis   (4). t. Two  screws  (5) Using  cross  tip  screwdriver,  install  two retained  screws  (5)  securing  side  panel (6)  of  power  control  chassis  (4)  to  power supply  chassis  (15). These  were  removed  in step  l. These  were  removed  in step  k. These  were  removed  in step  j. These  were  removed  in step  i. These  were  removed  in step  h.  See  figure  4-11. These  were  removed  in step  c. These  were  removed  in step  g. 4-134


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business