Quantcast REPLACEMENT  OF  LAMP  HOLDER  DS1 - TM-11-5820-890-30-5_450

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF LAMP HOLDER DS1
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  CIRCUIT  BREAKER  CB1.  Continued - TM-11-5820-890-30-5_449
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT  OF  RELAY  K1


TM 11-5820-890-30-5 4-32.  REPLACEMENT  OF  LAMP  HOLDER  DS1. Tools: 1/2-inch  open-end  wrench 1/2-inch   socket Flat  tip  screwdriver 9/16-inch   open-end   wrench 9/16-inch   socket Torque   screwdriver Torque  wrench Soldering  kit Expendable  Supplies: Cotton  swabs Solder Alcohol References: Paragraph  4-31  for  removal  and  installation  of  circuit  breaker  CB1. ITEM ACTION REMARKS REMOVAL a.  Mounting  adapter b.  Six  captive  screws  (13) and  front  access  cover (11) c.   Circuit   breaker   CB1   (10) d.  Lens  (16)  and  lamp  (15) e.   Wires f.   Lamp   holder   DS1   (11) INSTALLATION g.                     Lamp   holder DS1 (11) h.   Wires i. Lens  (16)  and  lamp  (15) Circuit   breaker j. CB1 (10) k.                  Front  access cover  (11)  and  six captive  screws  (13) Set  on  work  surface  with  left  side toward  you. Using  flat  tip  screwdriver,  fully  loosen  six captive  screws  (13)  securing  front  access cover  (11)  to  power  control  chassis  (10). Remove  front  access  cover.  Inspect  front access  cover,  replace  if  required. Remove  and  retain. Remove  and  retain  lens  (16)  and  lamp (15)  from  defective  lamp  holder  DS1  (11). Using  soldering  kit,  tag  and  desolder  wires from  defective  lamp  holder  DS1  (11). Using  9/16-inch  open-end  wrench,  remove and  retain  nut  and  Iockwasher  securing defective  lamp  holder  DS1  (11)  to  power control  chassis  (17).  Remove  lamp  holder through  front  of  chassis.  Discard  defective lamp  holder Position  lamp  holder  DS1  to  power  con- trol  chassis  (17)  and  install  retained  lock- washer  and  nut.  Using  torque  wrench  and See  figure  4-5. Refer  to  paragraph  4-31  for removal   procedures. See  figure  4-10. These  were  removed  in step  f. 9/16-inch  socket,  torque  nut  to  29  to  31  in-lb. Using  soldering  kit,  solder  tagged  wires Before  and  after  soldering, to  leads  of  replacement  lamp  holder  DS1 clean  wires  and  leads  with (11).  Remove  wire  tags.  Replace alcohol  and  cotton  swabs. insulation  sleeving  as  required. Install  retained  lens  (16)  and  lamp  (15) These  were  removed  in to  lamp  holder  DS1  (11). step  d. Install  retained  circuit  breaker  CB1  (10) Refer  to  paragraph  4-31  for in  power  control  chassis  (17). installation   procedures. Hold  in  place  and  tighten  six  captive  screws  See  figure  4-5. (13)  securing  front  access  cover  (11)  to This  was  removed  in power  control  chassis  (10).  Using  torque step  b. screwdriver,  torque  screws  to  8  to  10  in-lb. 4-127


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business