Quantcast REPLACEMENT OF RESISTOR MOUNTING BRACKET

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF RESISTOR MOUNTING BRACKET
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT  OF  RESISTOR  R3
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF DUMMY LOAD AND ATTENUATORS


TM 11-5820-890-30-5 3-36. REPLACEMENT OF RESISTOR MOUNTING BRACKET. Tools: 3/16-inch    nutdriver Cross  tip  screwdriver,  #0  point Adjustable  wrench References: Paragraph  3-25  for  removal  and  installation  of  test  adapter  from  maintenance  group  lid. Figure  3-12  for  illustration  of  resistor  R3  and  mounting  bracket. ITEM ACTION REMARKS REMOVAL a.   Two   screws   (75),   flat washers  (4),  and  hex nuts  (5) b.  Resistor  R3  (74) c.   Switch   S12   (11) d.   Two   nuts   (28)   and   flat washers  (29) e.   Resistor   R3   mounting bracket   (73) INSTALLATION f.   Resistor   R3   mounting bracket   (73) g.   Two   nuts   (28)   and   flat washers  (29) h.   Switch   S12   (11) i. Hex nut and Iockwasher j. Resistor R3 (74) k.   Two   screws   (75),   flat washers  (4),  and  hex nuts  (5) Using  cross  tip  screwdriver  and  3/16-inch See  figure  3-12  (sheet  3). nutdriver.  Remove  and  retain  two  screws, flat  washers,  and  hex  nuts  securing resistor  R3  (74)  to  mounting  bracket  (73). Remove  and  retain  from  mounting  bracket. Note  position  of  switch.  Using  adjustable wrench,  remove  and  retain  hex  nut  and Iockwasher  securing  switch  to  test  adapter. Remove  and  retain  switch. Using  adjustable  wrench,  remove  and  retain two  nuts  and  flat  washers  securing  mounting bracket  (73)  to  chassis  studs. Remove  and  discard  defective  mounting bracket   (73)   from   chassis   (67). Place  replacement  mounting  bracket  on chassis  (67)  and  aline  mounting  holes  with chassis  studs. Using   adjustable   wrench,   install   and   tighten   These   were   removed two  retained  nuts  and  flat  washers  securing  step  d. mounting  bracket  to  chassis  studs. Insert  retained  switch  into  test  adapter  so that  tab  of  washer  fits  into  hole  in  back  of test  adapter  front  panel. Using  adjustable  wrench,  install  retained These  were  removed hex  nut  and  Iockwasher  securing  switch step  c. to  test  adapter. Install  on  mounting  bracket. This  was  removed  in step  b. Using  cross  tip  screwdriver  and  3/16-inch These  were  removed nutdriver,  install  and  tighten  two  retained step  a. hex  nuts  (5)  and  flat  washers  (4)  on  two screws  (75)  securing  resistor  (73)  to mounting   bracket   (73). in in in 3-106


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business