Quantcast REPLACEMENT OF SWITCH FLEX ASSEMBLY. Continued - TM-11-5820-890-30-5_206

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: REPLACEMENT OF SWITCH FLEX ASSEMBLY. Continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REPLACEMENT OF AUDIO FLEX ASSEMBLY. Continued - TM-11-5820-890-30-5_205
Up
TM-11-5820-890-30-5 Ground Non-Icom Radio Sets Consisting of: Receiver-Transmitter Radio RT-1439/VRC (NSN 5896-01-195-0827) Manual
Next
REPLACEMENT OF SWITCH FLEX ASSEMBLY. Continued - TM-11-5820-890-30-5_207


TM 11-5820-890-30-5 2-52. REPLACEMENT OF SWITCH FLEX ASSEMBLY. Continued ITEM ACTION REMARKS REMOVAL Continued f.   Retaining   nut Use  5/16-inch  socket  and  socket  wrench. Remove  and  retain  retaining  nut  securing DIM  variable  resistor  to  RT  front  panel  as- sembly. g.   Retaining   nut Use  9/16-inch  socket  and  socket  wrench. Remove  and  retain  retaining  nut  securing FCTN  rotary  switch  to  RT  front  panel  as- sembly. Use  3/4-inch  spanner  socket  and  socket wrench.  Remove  and  retain  retaining  nut securing  RXMT  connector  to  RT  front  pan- el  assembly. h.   Retaining   nut Remove  and  retain  internal  tooth  Iockwasher from  RXMT  connector. i. Internal  tooth Iockwasher j. Switch  flex  assembly Remove  and  discard. INSTALLATION k.   Switch   flex   assembly Position  switch  flex  assembly  on  RT  front panel  assembly. l.             Retaining nut Use  9/16-inch  socket  and  torque  wrench. Install  and  tighten  retaining  nut  securing FCTN  rotary  switch.  Torque  nut  to  29  to 31  in-lb. m.              Retaining nut Use  5/16-inch  socket  and  torque  wrench. Install  and  tighten  retaining  nut  securing DIM  variable  resistor.  Torque  nut  to  11  to 13 in-lb. Retaining  nuts n. Use  3/8-inch  socket  and  torque  wrench. Install  and  tighten  retaining  nuts  as  follows: CHAN  rotary  switch:  11  to  13  in-lb. MODE  rotary  switch:  11  to  13  in-lb. RF  PWR  rotary  switch:  19  to  21  in-lb. Obtain  new  internal  tooth  Iockwasher and  place  on  RXMT  connector. o.  Internal  tooth Iockwasher Retaining nut p. Use  3/4-inch  spanner  socket  and  torque wrench.  Install  and  tighten  retaining  nut and  internal  tooth  Iockwasher  securing RXMT  connector.  Torque  nut  to  88  to  92 in-lb. NOTE Position  retained  knobs  on  shafts  aligning VOL  control  knob  shaft knob  set  screws  with  flat  surface. must  be  pressed  in  before installing  knob. q.   Knobs 2-185


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business