Quantcast CHAPTER 6 FILL DEVICES

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: CHAPTER 6 FILL DEVICES
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
CABLE SCHEMATICS (cont)
Up
TM-11-5820-890-20-2 Ground ICOM Radio Sets Manual
Next
AUTOMATED NET CONTROL DEVICE (ANCD). Continued


TM  11-5820-890-20-2 6-1 CHAPTER 6 FILL DEVICES Subject Para Page General 6.1 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automated Net Control Device (ANCD) 6.2 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ECCM Fill Device 6.3 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1. GENERAL. The SINCGARS radio may be loaded with required data in two ways. The primary method is by use of the Automated Net Control Device (ANCD) (AN/CYZ 10), which loads the radio with both COMSEC keys and frequency hopping (FH) data. The other method involves the use of a COMSEC fill device (KYK 13, KYX 15, KOI 18) to load COMSEC keys and an ECCM fill device (MX 18290) to load FH data. This chapter provides minimum essential guidance to the unit level maintainer regarding maintenance of the ANCD and ECCM Fill Device. 6.2. AUTOMATED NET CONTROL DEVICE (ANCD). a. Maintenance Concept.  The maintenance concept for the ANCD is for the unit level maintainer to requisition and repair all external parts in accordance with TM 11 5810 394 14&P. If the problem is internal, unit maintenance personnel will use BIT software to determine the operational status of the ANCD. If the BIT confirms that the ANCD is faulty, unit maintenance will turn in the faulty ANCD through normal supply channels to a COMSEC depot. The unit will then requisition a replacement ANCD through normal supply channels. Also, replacement ANCDs are available at brigade and higher level signal offices for temporary loan to units needing replacement ANCDs. Unit SOP should indicate how temporary replacement ANCDs are to be provided to subordinate units. b. Battery Replacement.  All ANCD users, including operators, are required to change the ANCD batteries whenever necessary. Batteries should be changed as soon as feasible after the •LOW BAT" message appears in the ANCD display window. The ANCD will retain data for two minutes after the batteries have been removed. You will have two minutes to complete battery replacement, or all  data stored in the ANCD will be lost. The procedure for changing ANCD batteries is as stated below and as shown in the accompanying graphic. (1)   Using a coin or screwdriver, remove four screws and battery compartment cover from the ANCD. (2)   Remove the battery housing from the ANCD. (3)   Remove batteries from the battery housing and replace them, maintaining proper polarity. (4)   Insert the battery housing into the ANCD, again ensuring proper polarity. (5)   Install the battery cover and tighten screws to a firm setting. (6)   Turn the ANCD ON and verify that battery change was successful.


Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business