Quantcast CHAPTER 2. INSTALLATION - TM-11-2300-364-15-10003

 

Click here to make tpub.com your Home Page

Page Title: CHAPTER 2. INSTALLATION
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home

   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
CHAPTER 1. INTRODUCTION - TM-11-2300-364-15-10002
Up
TM-11-2300-364-15-1 Instruction for Installing Radio Set AN/VRC-46 AN/VRC-53 OR AN/GRC-125 and Intercommunication Set AN/VIC-1(V) Manual
Next
Figure 2-1. Cable Assembly, Special Purpose, Electrical CX-4722/VRC connector disassembly


TM 11-2300-364-15-1
CHAPTER 2
INSTALLATION
Section I. SERVICE UPON RECEIPT OF EQUIPMENT
by comparing the parts received with the items listed on
2-1. Unpacking
the installation drawings (Figs. 2-4 and fig.' 2-5).
Report all discrepancies in accordance with TM 38-750.
Move the packing boxes close to the location where the
Shortage of a minor assembly or part that does not
installation is to take place and unpack the parts of the
affect proper installation or functioning of the equipment
installation unit. Be careful not to lose any of the parts.
should not prevent the installation units from being
installed.
2-2. Checking Unpacked Equipment
c.  When vehicles with radio sets are to be turned
in or transferred, communication equipment will be
a.  Inspect the equipment for damage incurred
removed and reinstalled in new replacement vehicles.
during shipment. If the equipment has been damaged,
Additional items which are required to complete
report the damage on DD Form 6 (para 1-3).
installations should be requisitioned as individual items.
b.  See that the equipment is complete as listed in
To determine the Federal stock number of authorized
the packing slip. If a packing slip is not available, the
items in the installation unit, refer to SB 11-131.
completeness of the installation unit can be determined
Section II. EQUIPMENT INSTALLATION
2-3. Tools Required for Installation
Caution: Vehicle master control switch should
be at OFF.
The tools required for installation of Radio Set AN/VRC-
(1) Identify all major parts and components in Radio
46 and Intercommunication Set AN/VIC-1(V) in Armored
Set  AN/VRC-46  and  Intercommunication  Set
Vehicle Launcher Bridge (M48A2 Hull) are a part of Tool
AN/VIC-1 (V) in basic and installation units with the
Kit, Radar and Radio Repairman TK-87/U and Tool Kit,
items as shown on figure 2-5.
Supplementary, Radar and Radio Repair TK-88/U. The
(2) Assemble and wire power plug and accessory
following additional items are needed:
assembly to the CX-4720/ VRC (fig. 2-5).
a.  1 electric drill (3/8 inch).
(3) Refer to cording detail (fig. 2-5) to determine how
b.  1 set of drill bits (1/16 inch to 3/8 inch).
the various components connect into the complete
communication system. For drilling and welding,
refer to figure 2-3.
2-4. Installation Instructions
(4) Secure equipment in place (fig. 2-5).
(5) Secure the cable assemblies in place by fastening
a.  To accomplish the installation, follow the
the cable clamps to the tapping pads provided in
instructions given below on those shown on figures 2-1
the vehicle. Engage all connectors in their proper
5


Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business