TB-9-2320-387-35-3

• INSTALLATION INSTRUCTIONS FOR SYSTEMS SINGLE CHANNEL GROUND AND AIRBORNE RADIO SYSTEM (SINCGARS) AN/VRC-88F, AN/VRC-90F FORCE XXI BATTLE COMMAND, BRIGADE-AND-BELOW (FBCB2) AN/UYK-128 (V)4
• INSTALLATION INSTRUCTIONS is changed as follows
• LIST OF EFFECTIVE PAGES
• REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
• TABLE OF CONTENTS
• TABLE OF CONTENTS-continued
• CHAPTER 1. INTRODUCTION
• CHAPTER 2. PURPOSE OF INSTALLATION
• CHAPTER 3. COMPLETION TIME FOR INSTALLATION
• CHAPTER 4. PREPARATION FOR INSTALLATION
• Section IX. C4ISR EQUIPMENT, DISTRIBUTION, AND CONSUMABLES
• Table 4-1. Kit Parts List for Installation of C4ISR Equipment.
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment.
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
• Table 4-2. Non-Kit Parts List for Installation of C4ISR Equipment (Contd).
• CHAPTER 5. INSTALLATION PROCEDURES
• Figure 5-2.
• Install grommet material
• Measure and cut terminal board
• Section IV. FUSE HOLDER COVER INSTALLATION
• Section V. ASSEMBLY OF CAB ENCLOSURE PANEL
• Install 24V terminal board
• Section VI. FINAL ASSEMBLY, TERMINAL BOARD WIRING, AND TERMINAL LINK
• Position cab enclosure panel
• Route 24V power cable
• Install cab enclosure panel
• Secure three 24V fusewire assemblies
• Section VII. INTEGRATED RACK INSTALLATION
• Install keyboard stowage box
• Install W3 cable
• Fabricate ground strap
• Position integrated rack
• Figure 5-22.
• Section VIII. SINCGARS MOUNTING TRAY, AMP GUARD, AND FBCB2 COMPONENTS INSTALLATION
• Place mounting bracket
• Install CPU isolation kit
• Figure 5-27.
• Insert weldment
• Insert footrest weldment
• Connect W2 cable
• Install Vehicular Amplifier Adapter (VAA)
• Section IX. LOUDSPEAKER INSTALLATION
• Using mounting plate
• Section X. LOUDSPEAKER CABLES INSTALLATION
• Section XI. PLGR BRACKET INSTALLATION
• Secure mounting bracket
• Install PLGR mount assembly
• Section XII. PLGR ANTENNA AND CABLE INSTALLATION (WITHOUT BOLT-ON ARMOR)
• Remove wiper access cover
• Install antenna cable
• Remove screw
• Route antenna cable
• Section XIII. PLGR POWER CABLE INSTALLATION
• Section XIV. EPLRS MOUNTING CABLE INSTALLATION
• Using EPLRS bracket
• Install shelf
• Section XV. EPLRS URO (USER READOUT) INSTALLATION
• Using URO bracket
• Install URO bracket
• Section XVI. ANTENNA INSTALLATION
• Figure 5-54.
• Figure 5-56.
• Install antenna overcab mount
• Install antenna
• Position antenna with base
• Section XVII. CABLES INSTALLATION
• Route power cable
• Route INC-EPUU cable
• Figure 5-65
• Route cables
• Figure 5-69.
• Figure 5-70.
• Route SINGARS antenna cable
• Section XVIII. DVE HOOD CABLE GUIDE INSTALLATION
• Locate, mark, and cut area
• Section XIX. DVE PAN AND TILT MODULE (PTM) MOUNT ASSEMBLY PREPARATION AND PILLAR MOUNT INSTALLATION
• Section XX. DVE A-FRAME CABLE GUIDE AND PAN AND TILT MODULE (PTM) MOUNT ASSEMBLY INSTALLATION
• Using A-frame cable guide
• Install PTM mount assembly
• Section XXI. DVE DISPLAY CONTROL MODULE (DCM) ROOF MOUNT INSTALLATION
• Figure 5-81.
• Install four rivet nuts
• Install DCM B-pillar roof bracket
• Install DCM roof mount bracket
• Install vehicle soft top
• Section XXII. PAN AND TILT MODULE (PTM) CONTROL MOUNTING BRACKET INSTALLATION
• Section XXIII. PAN AND TILT MODULE (PTM) CONTROL ASSEMBLY, CONTROL CABLE ASSEMBLY, AND DCM/PTM INTERCONNECT CABLE INSTALLATION
• Figure 5-88.
• Secure PTM connector end
• Figure 5-91.
• Route DCM/PTM interconnect cable
• Section XXIV. LCD PROTECTIVE ASSEMBLY INSTALLATION
• Section XXV. DVE POWER CABLE INSTALLATION
• Figure 5-99.
• SECTION XXVI. WINDSHIELD ARMOR MODIFICATION
• Figure 5-101.
• Spot paint all exposed metal surfaces
• Section XXVII. ARMOR AND ANTENNA INSTALLATION
• Install wellnuts
• Figure 5-105.
• Install modified upper capping ring
• Secure antenna
• Section XXVIII. ANTENNA CABLE INSTALLATION (WITH BOLT-ON ARMOR)
• Split grommet
• Remove five screws
• Install five inserts
• Figure 5-114.
• Figure 5-116
• Blank Page
• Blank Page
• TB-9-2320-387-35-3
• Distribution
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Distribution
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page
• Blank Page
• Blank Page
• Blank Page
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS
• Blank Page

Privacy Statement - Press Release - Copyright Information. - Contact Us